Hot Selling Glazed Porcelain Tiles

Ref Price:
Loading Port:
Shekou
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
1000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:


specifictions

  1. various sizes are available;

  2. More than 100 design andcolors;

  3. Both waterproof and nonwaterproof available;

  4. Strict control on colortolerance;

  5. Perfect effect on flatness andglazed surface;

  6. Ink-Jet technology applicationon the tiles

  7. Stable production andsupplying;

  8. Competitive price and paymentterm

  9. Stable production andsupplying;

  10. Suitable for economic endusing;


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:floor tile question please help?
Get okorder.com/
Q:I am going to be using a self stick floor tile in a mobile home. What can I use under it as a vapor barrier?
I just replaced the bulk of my mobile home flooring with 12x12 self stick tile from Fred's.... 1. Take off the old flooring (Carpet or tile.) and get it back to bare wood (Plywood)..... 2. Repair any bad sections of old plywood... 3. Level any joints between patches and any nail heads (I use drywall screws...A lot better hold and faster to put in when using a drill.)... Also the best patching material is Bondo...The wood filler takes forever to dry and will not form a Strong surface...Bondo drys to HARD plastic within 15 minutes...And is very easy to sand or form with a Bondo file... Be sure that everything is smooth or any hail heads or depressions will show under the tile later on... (Bondo also hold up better in wet areas like the bathroom) Pop a chalk line down the center of the room and start putting the tile down from this center line...Its not as noticeable to have something slightly off along the wall line as it it in the center of the room...Also when you get to the walls or in those little tight areas you will want to measure and cut some of the tiles....To do this you need to measure where the tile is to be cut (Remember the arrow direction) then lay the tile over an old piece of tile (So you dont cut the good flooring) and using a steel straight edge and a knife scribe a line...Then bend the tile along the line and it will break cleanly along the line.. Pay attention to the arrows on the back of the tile and always point them toward the same direction... This makes the pattern come out right... The glue on the tiles will hold them in place if the floor surface is clean and dry... If the energy blanket under the home is gone it will still take YEARS to do any damage to the new plywood floor that you replaced...
Q:what size grout joints for ceramic tile?
It depends on the size of your tile. A lot of 4.25 inch tiles have spacers built in. When you put the tiles in it will give you a 1/8 in gap for you grout. I use 1/4 inch spacers when installing 12 inch tiles.
Q:Porcelain tile cutting, need help?
If you'd tried Big T advise and it didn't work then there's another way. Cut the tile in two pieces and notch out the pipe hole with a blade for cutting tile (a hand blade) it's easier then tossing out 22 bad pieces.
Q:How can I Remove stain from my Kitchen ceramic Tiles?
what is the stain caused from?
Q:i have tile for my walls in bathroom and a couple have fallen off?
let the wall dry , overnight if needed. use contact cement (because your tile is some form of plastic) this cement could be in a can, liquid form yellow in color , or could be obtain in spray . try Lowe's, home depot or any other hardware, even walmart. then apply on both surfaces;wall and tile , wait 15 mins. or more if is cold where you are.. and lay it in place. don't mess this motion or you wont be able to undo it unless you brake it . One note ,do not inhale this cement too long , or you will be higher than a kite.
Q:what kind of paint do you paint ceramic tiles with?
I would not try painting the floor, virtually nothing available will stay in place. You can use the 2 part epoxy paint for the walls, that is designed for re-coating a tub. It is about $50 for the kit, and one kit may not do the entire bathroom. Kilz, a brand name, does make a primer for going over tile. You should rough up the surface a bit with the sand paper, so the primer will stick, then put on a good finish coat. I did this in my bathroom with pink tile. It lasted about 2 years, I then had to touch up some nicks, but it was easier and much cheaper than all new tile.
Q:Tiling Advice urgently needed?
[1] Yes you can tile over the existing tiles, What you need to do first? Is to rough up with rough sandpaper on the existing tiles to give a bite for the new tiles to hold on. [2] It is better to have ready mix, because it will have every things in it [3] Most grout are waterproof and also you can get differ colour grouts to match your bathroom. [4] Put in your new suit first, then tiles on top of your existing tiles, and grouts it as well. [5] fill your bath first, then seal it, so it will have the weight of the bath and water in it and it wont break the seal and lest chance of a leak.
Q:Tiling the plane? need help asap?
i've got by no skill heard of no longer having the flexibility to apply your computer on the airplane. you probable would desire to have the blue-the enamel off. some planes (purely some southwest and delta planes) easily have loose wireless on the airplane. i've got used my computer on the airplane till now its no longer a concern. you purely can't use it till you get severe adequate up. they're going to inform you so which you are able to use authorized electronics (that comes with laptops!)
Q:how to install rectified tile?
it sounds like to me he's using a method called mud setting the tile,used on floors that concrete is low in spots,and sounds to me he knows what he is doing,

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range