HOT ROLLED STEEL COIL WITH HIGH QUALITY AND COMPETITVE PRICE

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
50 m.t.
Supply Capability:
5000 m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

HOT-ROLLED STEEL COIL

Hot rolled low hardness, easy processing, good ductility. 

Available specification


thickness

width(mm)

length(mm)

coil inside diameter(mm)

HOT ROLLED 

STEEL COIL 

1.5-25

600-2000


762

HOT ROLLED

STEEL STRIP

1.5-20

30-720


762

HOT ROLLED 

STEEL PLATE

6-700

500-4500

4000-18000


HOT ROLLED 

STEELSHEET

1.2-25

50-2000

0-18000


We can supply customers' with different specifications of  the highest quality and lowest price.

 

With excellent cold bending molded manufacturablity, good decoration effect, strong anti-corrosion ability, galvanized steel coils and sheets are also pollution-free and easily recycled. Accordingly, they can be used as final products and basic plates of color coated steel coils. 

 

Sincerely welcome to contact us for the future details if any item interest you ,and we will make every effort to assure that your requirements will be satisfied ,and we hope to establish long-term business relations with you on the basis of the equality and mutual benefit.

We are waiting for your email.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:what is the origin of stainless steel?
Stainless steel is regular steel. They just remove most of the carbon out of it. Carbon it the reactive element within the steel that makes it rust, tarnish, etc...
Q:Nylon or Steel strings for guitar?
Musical variety speaks volumes with regards to this trouble. Folks that need excessive volume will probably be unhappy with unamplified nylon string guitars. From my viewpoint, the basic change between steel and nylon is this: metal strings ring and nylon strings resonate. The volume produced via steel is usually a lot greater than nylon but, to my mind-set, the sound resonance produced with the aid of the wooden of your guitar is essentially masked by using steel strings. If you have a decently made guitar (often, around a thousand bucks and up), the sound interaction between the timber and the strings in a nylon guitar is magical throughout the complete frequency range. With a metal string guitar, the sound produced by using the vibrating string overpowers the timber resonance at all but low frequencies. Personally, i'll take a nylon string guitar any day for the sensitivity gained from the interplay between timber and vibrating string.
Q:Probability of steel hardness?
Suppose that the hardness of steel is uniformly distributed, taking on values between 50 and 80 on the Rockwell B scale. That would be... f(x) = 1/(80 - 50), 50 ≤ x ≤ 80 . . . . . 0 elsewhere Consider this following problem.. Compute the probability that the hardness of a randomly selected steel specimen is less than 60. Here, we have... P(x 60) Oh! Know that the mean and the standard deviation of the uniform distribution function are... µ = (a + b)/2 σ = (a - b)²/12 You should get... µ = 65 σ = 75 Now... P(z (60 - 65)/75) = P(z -0.07) Hence, you should get around 0.462. Good luck!
Q:AK47 firing through steel?
Yes it can, it also depends where the ammunition were made. Some ammunition made outside russia will not penetrate steel plates. Places like Somalia, Iran,and Iraq.
Q:Steel WareHousing.......?
Compared to what?
Q:Does stainless steel turn brown or bronze?
I would say don't wear it in the shower because it will tarnish and it could rust.
Q:What grade of steel is best suited for use on ships. Specifically trawlers?
How big is your trawler going to be and what use, The ones you see off the Alaska Coast or a Gulf Coast Shrimper? My preference in today's economy would not make sense and that is Aluminum.....not steel at all, maybe even Fiberglass, but $$$$ talk so Steel is cheaper, but you need to know what you are doing. The designer of the hull should have specified the right /preferred grade. It today's world there are many more choices available. You use a mild steel, most often grade A or B, but some applications call for grade D. Check your blue prints and list of materials. Edit. Ok I understand. There are 2 ways to go. One is use a relatively cheep steel and use higher cost epoxy primers and paint, often requiring special surface preparation just before priming, or two, using a much higher cost steel with more chrome and nickel in it. Grades that begin with #3xxx These are weldable with rods that are available, and can be welded directly to mild steels. However these are 3X the cost. If your a Shrimper, I'm guessing gulf coast. I worked with several boat yards in the 70's installing spray urethane foam for insulating there holes. So I've been around lots of small yards from Florida to Texas. I'd call the nearest steel warehouse and ask what they would recommend. You might find what you want at a scrap yard. I've lucked out several times picking up 1/4 plate scrap$ and I'd bet the scrapyard guy would know just what you need. I know there are places to get what you need in Mobile and New Orleans. Good luck!
Q:A question about steel?
I think it might be a bit brittle and could break from metal fatigue.
Q:Would aftermarket steel wheels weigh more than stock jeep wheels?
steel is steel is steel- they will always be heavy you would have to weigh them to find out--NOW if you are going to alloy wheels they are typically aluminum and yes they are lighter -this is good because it lightens your un-sprung weight and is less harmful to your suspension-good for your auto
Q:What is the malleable temperature of carbon steel?
It needs to be RED hot, the hotter the better. Yes you can use a camp fire if you put the file directly in the hottest part of the coals, but it'll take about 5-10 minutes to heat. Charcoal briquettes would probably work better as a heat source. You can use something like a blow dryer to intensify the coals, that might help. You'll also need a bench vice, and the biggest pair of pliers you can find, for leverage. Bending steel's not easy even when it's hot. You could also use a bit of steel pipe that'll fit over the end of the file. Stick the file in the vise when red-hot, slip the pipe over the free end, and use the pipe to bend it. OR, you could use the old-fashioned method of just holding it with pliers in one hand, and hitting it with a 5lb sledge hammer with the other. use something solid as an anvil, like a large steel pipe. you mighe be able to get away with using a small log, but you'll have to work twice as hard. Safety glasses are MANDITORY for this type of thing. Do not attempt without eye protection at all times. Ear plugs are also a very good idea.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range