Hot Dipped Galvanized After Welded Mesh
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. assortments for galvanized welded wire mesh panel:
hot dipped galvanized and electro galvanized
Material: iron wire
Diameter: 2-8mm
2.applications:
galvanized welded wire mesh panel of our xingxin metal mesh are widely used in construction reinforcement, the ground for the tunnels,bridges, highway, airport and wharf, construction of wall body, also in decorative architecture.
3.advantages:
welding firm, mesh hole even, the mesh surface smooth, corrosion resistance, strength, protective capability is strong.
4.wire panel edge:
open edge , flush edge
The fencing system is a modern welded mesh system. The panel benefits from two different edges; barbed and flush. Providing good see-through visibility this system will not only blend into its environment but is also extremely rigid with up to three horizontal profiles.
Fence heights available in 1.0m, 1.2m,1.5m, 1.8m, 2.0m & 2.4m.
Fence panels suit post centres of 2.0m,2.5m&3.0m
The panels are manufactured using 5.0mm thick wires.Galvanized 4.0mm and after PVC coating 5.0mm thick.
The mesh is configured to 50mm x 200mm and is welded at every intersection.
The system utilises our unique patented Hexaclip fixing which comprises and anti-tamper bolts.
To achieve additional security the panel can be installed so that the barbed edge is at the top of the fence so that it acts as a deterrent to would-be climbers.
Where safety is key, particularly on lower height systems used in a playground setting, the panel can be installed so the flush edge is at the top of the fence so there are no sharp hazards. If opting to install barb-down inverted clips need to be ordered.
- Q:Is it possible to protect the radiation around the computer with a wire mesh?
- I have not heard of the wire, the chassis cover is the original radiation ah. Just do not advocate bare metal battle (no chassis or 24 hours cover)
- Q:How does proe draw wire mesh?
- this curve you can draw their own equation can also be used to generate, I used here instead of sine curve example, sketched out a curve ,
- Q:How the wire is welded
- Resistance welding, solder joint relative to welding beautiful. iron wire. The use of resistance welding, can be in a very short time, high current welding.
- Q:Will the gray sand brick wall is full of hanging wire mesh?
- because the wall will be settled with the beam after the column There are cracks, nail on the barbed wire and then wipe the cement mortar,
- Q:Why is the effect of electromagnetic radiation shielding with wire mesh?
- Do not believe ah, this can drop, who also buy shielding materials ah; direct purchase of barbed wire on the line.
- Q:Is the warm tube laid on top of the steel wire or below?
- and that the road is broken, then the loop must be replaced by all the warm pipe, which means that your room layout of the road to warm all the area to all Out of all to replace the new pipe to replace.
- Q:What is the mesh in the wire mesh specification?
- The smaller the mesh, the worse the ink passes, the larger the mesh, and the better the ink passes. In the selection of screen can be printed according to the accuracy requirements, select a different mesh mesh.
- Q:Barbed wire fence is what the iron ring
- Thorns are divided into ordinary wire and barbed wire. Surface treatment process: electro-galvanized, hot-dip galvanized, plastic, spray
- Q:Barbed wire mesh 20 mesh and 30 mesh what is the difference
- The mesh count refers to the number of holes of 2.54 cm. The unit used to express the mesh in the mesh product specification is hole / cm or line / cm. In countries and regions using imperial units of measurement, the mesh size is expressed in holes / inch or lines / inch.
- Q:How is the wire mesh made
- materials used generally use high-quality low-carbon steel or stainless steel. In general, it is necessary to produce a number of processes such as plate peeling, pickling, washing,
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Hot Dipped Galvanized After Welded Mesh
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords