Horizontal Multi-Stage Double Suction Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or L/C
Min Order Qty:
1 Set unit
Supply Capability:
1000 Sets Per Year unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Applications Power station/plant Water supply Municipal Construction Fire fighting Industrial Mining

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:how to remove rear bolt from water pump?
I would suggest removing the pulley but I dont know what kind of car it is.
Q:Do I need to replace my water pump or just the gasket on my '99 Passat?
Replace the pump. While your at it, since the front end (actually the bumper cover) is off, get the timing belt done, with rollers, tensioner, thermostat, and G12 coolant.
Q:Problem with my water pump!!?
Sounds like it's waterlogged. That's what it's called when the water and the air in the resevoir tank mix, and the volume of air gets so small as to not be able to provide any decent compression with which to push water through the system. At that point, any time you open a fixture, the pressure drops enough to turn on the pump, and when you turn off the pump, if it's just right, it will turn off and then back on, then off, then on, back and forth till you shut it off and it can set and stabilize, till you need water again. The solution is to reintroduce a sizeable amount of air back into the top of the tank. If it's an older tank, without a bladder, (identified by the small bulge around the center of the tank and either a blue or rust color), then the best way is to simply drain the tank and restart the system. That way it will trap all the air in the top of the tank and you'll have enough pressurized air to push a gallon or two of water out, before the pump needs to kick on again. If it's the bladder type, with the bulge, then the bladder has blown and you're, in effect, working with a standard resevoir tank now, except that it will have an air valve in the top like a bicycle tire, so you can pressurize it with an air tank. If so, open some fixtures, start pressurizing the top of the tank and blow all the water out of the system. Once it's dry, put about 20 lbs. of pressure in the tank and start up the pump. You should be good to go.
Q:hello i have a 1993 eagle vission my problem is yhat is overheating butt i have changed the water pump,radiato?
head gasket bad? engine timming off?
Q:how to change a water pump on 1999 chevy venture?
David okorder.com Once there sign up for there free account.Once your a member go to the repair section for your venture.In the engine repair section click on water pump.This will give you instructions and pic of how to remove and replace this water pump.This free site will also help with lots of other repairs on your venture.Best of luck.
Q:What is the difference between electrical/mechacal driven water pump?
Mechanically driven water pumps run off of a belt on the front of the engine to drive them where-as an electrical water pump is run by you guessed it electricity. Belt driven water pumps are much more common with electrically driven pumps usually used for high performance car so as not to rob horsepower from the engine by the force it requires to drive the pump.
Q:water well pumps?
it is very easy to do just email me. I'll send direction . I would say you have a small under ground stream of water . as you use the water from the well, it will take time to fill the well pipe again
Q:Where should I buy my new water pump?
You can buy your new water pump via Powamac, they are exceptional in services. They provide you pump which satisfy your needs completely.
Q:How much can you safely restrict a water pump's flow?
ditto to magic
Q:water pump leak headache?
It's not the pump that's leaking. The water ports to the pump pass through the aluminum timing cover, over time the aluminum corrodes and leaks between the block and the timing cover. You need to remove the whole works and replace the timing cover, may as well do the timing chain since you're in there.
Our wide range of products may be applied to numerous industries including to water irrigation, construction, municipal services and more. With four production bases, our facilities cover an area of approximately 210,000 square meters. Altogether, our group has 6 wholly-owned subsidiaries, 12 sales companies and more than 200 offices throughout the world.

1. Manufacturer Overview

Location Shanghai,China
Year Established 1993
Annual Output Value Above US$100 Million
Main Markets 11.11% North America
11.11% South America
11.11% Eastern Europe
11.11% Southeast Asia
11.11% Oceania
11.11% Mid East
11.11% Eastern Asia
11.11% Western Europe
Company Certifications ISO9001:2000;ISO14001:2004

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shanghai
Export Percentage 11% - 20%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: 30,000-50,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered
Product Price Range High and/or Average