Horiontal high-speed pump is a special pump that this company has absorbed internal and oversea advanced technology and developed combining internal applying field.
- Q:110 engine oil pump gear is always broken, what should I do?
- The crankcase needs a lot of cleaning. It's too dirty. It's stuck in the oil pump
- Q:When the car runs neutral, does the oil pump work?
- As long as the engine oil pump will work; but it is best not to in the automatic car speed of more than 60 temporal sliding block, then there will be damage to the gearbox is the main gearbox lubrication is not good
- Q:The van is out of order. What's wrong with it? Can it make a noise?
- The direct burning tile lubrication system basically does not work. The oil won't come. All moving parts are dry milled
- Q:Bending machine, cutting machine oil pump broken, how to judge?
- If it is winter, may be relatively thick oil, if it is not possible oil problems, there may be the problem of voltage, if it is the problem of the pump, it will not be less pressure is so simple. Where can you find someone to see?.
- Q:The car oil pump is broken. What are the problems?
- There's no trouble. You're not going straight
- Q:How to identify the motorcycle engine oil pump is normal?
- Determine whether the motor oil pump is normal, you can check the way through the oil lane to determine.An ordinary motorcycle, most of which will have an inspection screw on the cylinder head. It will have a copper pad to separate it from the other screws. After starting the engine, loosen the screw with a wrench. If the oil runs out of the screw at this time, the oil pump will be normal.If the engine does not have this screw or can not be found, it can also remove the cylinder head or the valve cover. After starting the engine, the oil will obviously pour out or eject, and it can also indicate that the oil pump is normal.If there is no engine oil within a few seconds after starting, it shows that the oil pump or oil channel is defective and should be shut down immediately.
- Q:Automobile oil pump fault
- Such a problem can arise. The oil pressure is too high, and the oil filter is opened by "drum". The reason is that the oil pump pressure limiting valve [pressure relief valve], resulting in a failure, can not normally open at high pressure caused by pressure relief
- Q:How can Honda know when the pump is broken?
- Hello, check whether the oil circulation, steel cap is on the oil, I hope my answer can help you, I wish you a happy car!!
- Q:How do I see the motorcycle's oil pump is broken? Two red
- Hello, friend. First of all, tell you that the two stroke motorcycle does not have an oil pump. If it's a four stroke. In 70, 90100 of the three models you can put the screws on the cylinder head of the lower right to loosen the. Then start the locomotive. If there is oil to the outside, then that the normal oil pump. If not, check the oil pump wheel for wear first. Because the oil pump wheel wear, even if the oil pump is not bad. It doesn't work either. The three models are identical in structure. Their oil pumps and pump wheels are relatively easy to break. Another 125 models, men's and women's pedals. Men's words a screw is loosen cylinder head top, then start. Organic oil emits just normal. No oil smoke, also want to look at the screen is not blocked. The screws on the ladies pedal are the same as the 7090100
- Q:How to check the motor oil pump oil supply is normal?
- In the premise of the normal amount of oil, usually need to check whether the oil pressure is normal (usually around 0.3MPa), if the oil pressure is low, usually the oil circuit, overflow valve failure or oil pump failure. After cleaning and adjusting the oil relief valve, the pressure is still low. The fault must be the oil pump failure.The effect of the oil pump is to press the engine oil to a certain pressure and force it to the surface of each part of the engine. If the oil pump is damaged or leaking, it is necessary to disassemble the oil pan, take out the oil pump and replace it, and clean or replace the oil pump inlet strainer at the same time.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average