Home Wall Mounted Dehumidifier

Ref Price:
$103.00 - 10,000.00 / unit
Loading Port:
Payment Terms:
Min Order Qty:
1 Set unit
Supply Capability:
500 Sets per Month unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

home wall mounted dehumidifier


1. Dehumidifying principle: 

    Adopt high performance cellular adsorption wheel,divided into moisture absorption area and regeneration area.When wheel rotates,moisture in the air adsorb in the wheel micro hole,make dry air into the indoor.When the moisture absorption wheel rotates to regeneration area,at this time,regeneration air(warm air) from reverse direction will drive moisture(wet air) absorption of the wheel to outdoor.Wheel repeat moisture absorption and regeneration action,has no influence on air flow,can continuously provide dry air for indoor.





Dehumidifying capacity    L/d


Wind capacity                m3/h


Weight                             Kg


Dimension          (L*W*H,mm)


Power                             KW



3.Environmental conditions:

   There is no condensed water because of dry dehumidification method,so dry dehumidifier can work at temperature -30°C~60°C.


4.Lower humidity:

   Relative humidity can reach less than 1% for some special needs because of adsorption    dehumidification.


5.Environmental protection and energy saving:

   Reach dehumidification purpose without any cold medium,save energy consumption.



   Apply to family,basement,warehouse,port crane tower room,bridges,metal rust,

electric control room,brewing,chemistry,chemical engineering,electronics,food,

pharmaceutical,film,electronic,food,leather,military equipment,precision components,seeds,sugar,packaging,dairy products, fertilizer,tea,coffee,hygroscopic powder and other occasion.     



Q 1.Okorder Quality Control?
We hold a very strict quality control system to check every connector of our products for

your safety.

Q 2: How do you care for your kitchen appliances?
A: Keep good Ventilation indoor. Open the doors of the kitchen appliances, if not. There

will be some mildew on cutting board and other kitchenware, because the water vapor can not

evaporate easily.
Keep clean of all the appliances. Each kitchen has its special cleaning fluid,please go to

Kitchen cleaning stores buy some clean them on time.

Q 3: Which one do you use the most of kitchen appliances?
A: Assuming you mean small appliances .I say too many! At one time we would buy every one

that came along; including a hot dog machine, pizza maker, elec. carving knife, elec.,

toaster oven,. Most have been garaged sale (sold) or are stored in the garage. Most used;

coffee maker, microwave, blender and mini food processor. OK?






Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the methods of use of the dehumidifier?
The cooling water and drying of the wet air can be realized by using a water spraying meter combined with a water spraying chamber and a watch and a cooler. In addition, cooling and dehumidifying of air can be realized by using a special cooling and dehumidifying equipment - a freeze dehumidifier
Q:What shall I do if the heating indicator of the air dryer is not extinguished?
Check to see if the temperature sensor is damaged or malfunction fails
Q:What is the mean of dryer?
A dryer is a mechanical device that vaporizes by heating the moisture in the material (usually water or other volatile liquid components) to escape the solid content of the specified moisture content.
Q:What are the characteristics of a convection dryer?
The temperature of the hot gas stream can be increased to the maximum temperature (about 730 DEG C) that the common metal material can tolerate. The radiation heat transfer will become the main mode of heat transfer at high temperature, and can achieve a high utilization rate of heat
Q:What are the factors that affect drying effect of dryer?
In the dryer, the first is to remove the moist air so that it contains very little residual moisture. The air is then heated to decrease its relative humidity. At this point, the steam pressure of the dry air is low. After heating, the water molecules in the particles escape from the bond force and disperse into the air around the particles
Q:How to install the car air dryer?
The length of the line from the air compressor to the dryer shall be required to ensure that the air temperature at the inlet of the dryer meets the technical requirements
Q:What are the common breakdowns in the automotive dryer?
Air compressor dryer inlet condition is good, normal, but output "(1{) is extremely poor, then there are two causes, one is the desiccant moisture, oil, thus blocking off the impurities exceed the standard, the other is on the dryer outlet hole; a one-way valve 2 stuck, that dryer is very long time without maintenance, please put a" dry assembly removed, a complete system maintenance
Q:What are the cautions in the use of dryers?
When moving the dryer, hold it in both hands and press the lid tightly with your thumb
Q:What are the clogging problems in dryer?
Refrigerant can not cycle, low pressure for negative pressure, air conditioning is not refrigeration.
Q:What are the drying agents that are often placed in the dryer?
Silica gel, montmorillonite, molecular sieve, mineral, fiber, activated carbon, lime and so on

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range