HK 2016 Needle Bearing HK Series High Precision

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
1 set
Supply Capability:
1000000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Specifications:



Brand Name:


Bore Size:

20 mm

Outside Diameter:

26 mm

Model Number:

HK 2016

Precision Rating:


Seals Type:

Open or Sealed

Number of Row:

Single Row

Place of Origin:

Jiangsu, China (Mainland)


Chrome Steel


Grease Lubrication


Plastic Bag and Box


HK 2016

Drawn Cup Needle Roller Bearing :

The outer ring of drawn cup needle roller bearing is punched with the high-quality steel sheet. The outer ring has thin wall.The drawn cup needle roller bearing has the characterstics of small radial section area, large load carring capacity ,less inertia and economic manufacture. It is suitable for small section heght, or when the housing bore isnot used for raceway , this type is recommended to use .The bearing is assembled into the housing bore under a certain pressure without fu rther axial location.


The draw up needle roller bearing generally takes its shaft diameter as the internal raceway .However , the proper LR type inner ring can be  used in accordance with application condition.

Our Advantages:

1. Excellent and high quality control

2. Prompt delivery

3. Competitive price

4. Small order accepted 

5. Customers' drawing or samples accepted

6. OEM service

Application Area:

Needle roller bearings are mainly used in car engines, transmissions, compressors, cranes, etc.



1.More than 28 years export experience

2.Strict quality control

3.Delivery in time

4.OEM service are available with good price

5.Low MOQ

HK 2016 Needle Bearing HK Series High Precision

HK 2016 Needle Bearing HK Series High Precision

HK 2016 Needle Bearing HK Series High Precision

HK 2016 Needle Bearing HK Series High Precision

HK 2016 Needle Bearing HK Series High Precision

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:how can i make my skateboard bearings cleaner and faster?
Eh, boiling water should clean out the old grease. Soaking em in charcoal lighter fluid would work also the use a light and thin oil like cooking oil instead of grease with reassembly.
Q:how do you tell your wheel bearings are going out?
a constant, persistent, squealing noise when the truck is moving, means bad wheel bearings, as far as the in out when it's parked, it due to weight transfer parked up hill weight is in back, parked downhill weight is in front parked level, weight is balanced.,. this accounts for wheel standing in or out
Q:How to lube main bearings on a ipso washer mod #ihfo55?
don't have the book google it and use the right MOdel number
Q:what types of bearings are used on a 225kW wind turbine?
External bearings are usually long life types and may be sealed or not, usually tapered roller bearings designed for angled loads. Internal bearings can be of several types used in different places. In some cases, bushings, rather than bearings, are used in part or for the whole thing. It all depends on the manufacturer.
Q:How much would it cost to get bearings fixed on a fourtrax 250 Honda yr 2000, just a rough estimate please.?
What bearings? Wheel bearings are cheap and a DIY job. Engine/transmission bearings? They are more expensive and the labor to change them will run into the hundreds. Axle or steering bearings fairly cheap and yet another simple DIY job.
Q:My bones skateboard bearings are stuck?
Sounds like you bent the shields when you inserted them, or put them too far in. The shields should be flush with the edges of the bearings. This is assuming that the bearings spun without the shields. You did remember to not use water-based cleaners on the bearings?
Q:How do you change rear bearings on a 94 thunderbird?
rear bearings in the engine or the differential. the two are very different but either one would be a project. the engine, you would have to pull the engine out or pull the oil pan off and deal with it that way. pull all of the main bearing caps and replace them. the rear end is a bit more complex as you have to pull the axles out, pull the carrier and start from there.
Q:Can you put abec7 bearings in a wave board?
ABSOLUTELY! I've been ridin' The Wave for a couple of years now, and I def switched over to better bearings once I was ready. You def want to make sure that you have mastered ridin' the board before you make the switch. I'm pretty sure that Street Surfing is going to start making upgrades available, but until then, go for it. Just be ready for the faster speed. If you haven't checked out their website I'd give it a look, some cool vids/pics there, even some 'how to' vids if you're looking for some tricks to do ( THEWAVE.COM ). Hope that helps you out, the answer to your question is YES! Upgrading the bearings is something that anyone can do to their wave board, I would actually suggest it for more experienced riders. See ya on the Streets!!!
Q:Do skateboard bearings fit quad skate wheels which are attached to 7mm axels?
Skateboard bearings would work, since they are basically the same size as blading bearings. I would recommend Bones Bearings, it doesn't matter which Bones bearings, but here is a short review for Bones: Bones Reds-Best bearings under $20. Spins fast, and smooth. Bones Swiss-Best bearings under $55. One of the bestselling bearings in the world. Spins for about 20-60 seconds. Very fast, and smooth. Bones Super Swiss 6-About $60. An upgraded or better version of the Bones Swiss. Spins a lot smoother, quieter, and faster. Bones Labyrinth- Stronger, faster, and longer-lasting. Costs about $60. Bones Ceramics-The Best bearings ever created. The toughest, fastest, and used by speedy pro skateboarders and bladers. $140, it could last longer than 3-5 years with proper cleaning every 6 months. Also, Bones bearings are not rated ABEC, because ABEC are mostly for machinery. Bones bearings are Skate Rated, specially designed for action sports such as skateboarding and inline skating. Although Abec 7's or 9's would be great, Skate Rated bearings are better. So yeah skateboard bearings are pretty good for 7mm because my cousin had the same size of axles and he uses skateboard bearings. Hope it helps. :)
Q:which climate cause skateboard bearings to spin faster in the heat or in cold climate?Does heat cause bearings
It depends on the type of lubricant in the bearing. At higher temperatures the viscosity of the lubricant will be such that it moves through the medium faster. Higher temp, faster.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range