High Quality Male threaded elbow Male threaded elbow

Ref Price:
$2.51 / watt
Loading Port:
Ningbo
Payment Terms:
TT or LC
Min Order Qty:
1000 watt
Supply Capability:
100000 watt/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

High Quality Male  threaded  elbow Male  threaded  elbowppr fittings HYOSUNG PPR raw materials standard:DIN8077-8078            GB/T18742.3-2002             PN25            White grey green color

1.Material:Random Polypropylene(Hyosung R200P); 
2.ISO9001&ISO14001; 
3.Standard:GB/T 18742.3-2002, DIN8077/8078; 
4.OEM also ok

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Who knows the size of the PVC pipe and what is the maximum and minimum size?
Because of its harm to human body, Europe, Japan and South Korea and other countries have restrictions on using PVC as raw material and products. PVC resin has the advantages of plastic products is generally difficult to burn, abrasion resistance, chemical resistance, low leakage, good gas vapor. In addition, comprehensive mechanical energy, products transparent, electrical insulation, insulation, noise elimination, shock elimination, or better, is the most superior price than the general type of material. The defect is thermal stability and shock resistance is poor, whether it is hard or soft, PVC is easy to produce brittle during use. General PVC is not containing the relevant national standards allow the use of two (2 - ethylhexyl) adipate plasticizer (DEHA), DEHA in the high temperature (over 100 degrees Celsius) easily released, after contact with human health hazard. Because PVC is a hard plastic, to make it soft, a large amount of plasticizers must be added. Plasticizers are easy to release in a heated environment. If you are using DEHA, it will interfere with the human endocrine, cause women to breast cancer, birth defects, reduce the number of male sperm, or even mental disorders.
Q:Antistatic flame retardant PE plastic pipe installation, what should pay attention to?
1 、 cut the pipe according to the required length, remove the burr of the pipe port and chamfer 30 degrees.2. Insert the pipe into the bottom of the pipe mouth and mark it at the interface of the pipe and the pipe. Then mark the tube out of the 10mm with this mark. Make second more marks. Clean the outer side of the pipe and the inner side of the pipe. Apply a lubricant (not oil or grease).
Q:What are the manufacturing processes of plastic pipe fittings?
Vacuum - hot melt extrusion - vacuum sizing - two spray - print traction ---- product cutting ---- visual inspection ----Package warehousing
Q:What are the classifications of plastic pipes and fittings in the enterprise standard?
Plastic pipe as an important part of chemical building materials, with its superior performance, health, environmental protection, low cost and widely accepted by the majority of users, mainly UPVC drainage pipe, UPVC pipe, aluminum-plastic composite pipe, polyethylene (PE) pipes, hot water pipes which are polypropylene PPR.
Q:The difference between the hot melt connection and connection to electricity
Cost: hot melt than electric melting time: electric melting heat, low melting fast, less than 90 of the diameter of PE pipe can only use electric connection, different manufacturers, different grades and SDR welding pipe fittings, pipes and tubes, pipes and pipe fittings, pipe fittings can only use electric melting connection
Q:Antistatic flame retardant PE plastic pipe installation?
1 、 cut the pipe according to the required length, remove the burr of the pipe port and chamfer 30 degrees.2. Insert the pipe into the bottom of the pipe mouth and mark it at the interface of the pipe and the pipe. Then mark the tube out of the 10mm with this mark. Make second more marks. Clean the outer side of the pipe and the inner side of the pipe. Apply a lubricant (not oil or grease).3. The special rubber sealing ring is coated with lubricant and put into the pipe groove, and the pipe is directly inserted into the pipe fitting to the second mark.
Q:Method for using steel wire mesh skeleton plastic composite pipe
When the cut pipe or pipe fittings are connected with the original pipeline, the angle must be reasonable, no tension or other force can be avoided, and the electric welding pipe can be displaced during welding so as to leak water.
Q:What are the differences between electrofusion welding, hot melt welding and welding connection?
Hot melt is to use materials for heating and melting of special equipment, and even after the material is cooled. The hot melt pipes used in the project are all hot melt, and the construction is convenient and economical;
Q:Can the PPR pipe be injected with the same pipe as the PVC pipes?
Used machines look at machine precision. The main view is whether the template is even, and whether the track is worn badly. Second, look at the circuit is chaotic, chaotic, indicating that many times the maintenance, the oil circuit is leaking, leakage, that is already very old.
Q:Municipal water supply pipeline is a plastic pipe, then its matching valves and fittings are plastic?
Municipal water supply pipe for water supply plastic pipe, the pipe supporting accessories, such as three pass joints, valves, etc., can be chosen according to specific circumstances.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range