Q:like in movies how do you connect like some wire to start the car? also which wires? I'm curious not trying to take anyone's car.

Connect wire 'A' to wire 'B'...Briefly touch wire 'C' to wire 'D' (until engine starts) see figure 1. Disclaimer: These instructions are not to be used for illegal purposes...

Q:To help clean things up and make wiring a little more simpler on my jeep i got a fuse/relay box off an old junk car. i want to wire my off road lights into this relay box but i'm not sure what size wire is in the box it appears to be either 18 or 16 AWG one place said to strip the wire and measure the wire another says measure in the insulation. i'm not sure what to do. but if it is 18 awg would it hurt to go to a bigger size after the fuse box to my lights or should i rewire the whole box?

you have a relay wiring kit precise? the possibility of the relay ought to be saved contained interior the engine compartment. after all the possibility of the substitute ought to be proper as follows: discover you fuse block placed contained interior the cab. under sprint left section perhaps (I truthfully have a 'ninety 8 F150, no longer useful of differences) next stumble on an empty slot that isn't in use (no fuse in place). you additionally could make the relationship with a lady flat a million/4 connector to male connector placed on the shrink back of the fuse block. i ought to top be incorrect on the form of connector, yet you will see the way it rather is suitable as quickly as you stumble on it. you may discover the headlight circuit in case you choose them to close off with the headlights. shop in strategies you choose for to coach a relay so it won't overload the headlight circuit when you consider which you're putting on some heafty lighting fixtures furnishings on it. Sorry i'm in a hurry as we talk yet choose this facilitates. i visit make particular shrink back later to substantiate if to any extent further useful perfect ideas are obtainable in, and upload extra useful if needed. good fulfillment guy.

Q:I have a Hunter 5 minute fan. I have four wires coming from my ceiling. Red, Black, White, and Bare Copper. The Fan has a Green Wire, Black Wire, White WIre,and a Black/White striped Wire. The Ceiling Plate also has green wire. I know to connect the black to black, red to black/white striped, white to white. But for the green and copper wires, do I connect the copper wire from the ceiling to the green wire in the ceiling plate and also to the green wire from the fan?

As typical color coding goes in 110/120 volt A/C; Black = hot lead White = neutral Green = ground In house wiring the ground is typically bare and has no coating. Typically the fan and the mounting plate will have green wires to ground out the fan and the electrical box. If you have a ground wire (bare copper wire) you should hook to there. Update - - - Curtis is right, below this post. Your box is not set for a ground. Being that old of a house there is no telling what mods have been done. The neutral (white) and the ground (green or bare copper) are the same but different. The ground goes to the ground at your house. The neutral is the return to source (generating station). The ground helps make the electricity go the path of least resistance as soon as possible in the case of a short.

Q:I'd like to know what quot;wiremeans when it refers to computers. Is it the computer itself or the Internet?

Need context to answer your question. Can you give us the complete sentence in which the word appears? EDIT: Thanks for the clarification. Over the wire or Across the wire refer to the days when things were done by telegraph, which was a wired way of communication in the days before computers. If an announcer is, say, 70 years old, he might still use the expression, even though it would now mean that he just got the news. And he would have received it by phone or via computer.

Q:A 5.07 m length of 2.1 mm diameter wire carries 703 mA current when 22.3 mV is applied to its ends. Determine the resistivity of the wire.

Resistance of a wire in Ω R = ρL/A ρ is resistivity of the material in Ω-m L is length in meters A is cross-sectional area in m? A = πr?, r is radius of wire in m Use current and voltage to determine resistance. Plug that into the above and solve for ρ. Be sure to change numbers into meters.

Q:I'm trying to install a ceiling fan but I'm having trouble with the wiring. Coming out of the fan I've got a black, white, black and white striped, and a green wire. coming out of the cieling i've got a black, a white and a red wire.The fan's green wire is connected to the bracket as a ground, so that's out of the way. It's the other wires that confuse me. I've tried, white to white, black to black, and BW striped to red, but that didn't do anything.Any ideas? Thanks.

The wires on the fan; the white wire is the neutral, The black wire and the black/white wires are the hot wires on the fan, one goes to the fan and the other goes to the light. The wires in the ceiling; The white wire is the neutral, it gets connected to the white wire on the fan. Check the black wire and the red wire to see if they are both hot. If not, and the black wire is hot and the red wire isn't. the red wire feeds another circuit somewhere. If the wire feeds another circuit, tie the red, black wires in the ceiling together with the black and black/white wires from the fan. Is there an outlet or light not working somewhere? If they are both hot, connect one to the black wire and the other to the black/white wire. Is there a wall switch involved here? If so, when the wall switch is turned on, does it liven either the red or black wire? If this is the case, the wire that comes from the switch should be connected to which ever wire on the fan is the hot lead for the light. The other wire in the ceiling would be connected to the hot wire for the fan. There's lots of different scenarios that are possible. If you aren't sure of what you are doing, GET SOME KNOWLEDABLE HELP TO CHECK OUT THE WIRING! No sense burning your house down to save a few bucks by not hiring a professional.

Q:What is a tubeless wire and how does it work?

It is a wire without a tube. It works properly, it has a larger section than the usual wires, but is cheaper (Al is cheaper than Cu).

Q:My tail light work but when i hit the breaks everything go out. Any answers? Standard 4 wire

I believe that you have a bad gound wire, i realize that the ball should be enough to ground it , but it dosen't always work like that , so make sure that your white ground wire `is hooked up to your truck frame and the white wire coming from the trailer is connected to the frame of the trailer

Q:my internet wont pick up my wireless adapter thing now, because the internet box was reseted. How can I change it to wired?

Depending on your setup, you'll need to connect your Xbox and router (internet box) with an ethernet cable

Q:when wiring subs to different ohm levels, does is matter what kind of speaker wire you use to connect to the + and - terminals? i mean like gauge wise of the speaker wire and such.

Too big of wire is just a waste of money. As Rick said, 12-16 is ideal for subs. 10 AWG would be the maximum size required.