Q:The expert can tell me how to install this valve, and what fittings to use on both sides

On the first floor, the two floor adds up to the perfect answer: look at the flow direction and weld it directly to the pipeIf the process permits, you can first weld on both sides of the flange, modified into a flange butterfly valve, and then installed on the pipe, easy to overhaul later

Q:What is called protective valve, and other valves what is the difference?

Protection valve should be in the air defense valve, can be copper gate valve. (according to the specific use of civil air defense requirements, design institute does not count).2, while the protection valve should be a locking device with the valve, not the general valve can be replaced.

Q:What kind of valve is it? How do you see the status of the switch?

This is called gate valve. The core is opened and the core is screwed down. Turn left and right.

Q:What does the "Z45T-16" valve mean?

Z - gate valve4 - flange connection5 - Dark pole, stem non lifting (gate valve structure)T - copper alloy, valve sealing face code16 - pressure code, 1.6MPaMaterial code for grey cast iron valves of nominal pressure less than or equal to PN16 shall be omitted in model preparation.May refer to JB/T 308 valve model compilation method

Q:Which valves are installed in a directional manner?

Depends on the specific valve is one-way seal or two-way seal?

Q:How to better maintain the valve?

We should keep the valve cleanWe should regularly check and maintain the integrity of the valve the other components. As a fixed hand wheel nut fell off, to be filled and can not manage, otherwise it will grind the valve stem upper garden square, gradually lost with the reliability, and even can not startWe do not rely on the valve support other heavy objects, do not stand in the valveThe stem, especially the threaded part, to regular cleaning, the dust has been soiled should be replaced with a new lubricant, because the dust contains hard debris, easy to wear thread and stem surface, affect the service life

Q:What valves are needed on the construction site?

Order valves1, according to the use of place, use, and understand the relevant laws and regulations, specifications, standards, policies, approval may be used after the selection of valves suitable for various requirements;2, confirm the working conditions of valve, applicable medium, working pressure and medium temperature;3, determine the nominal diameter corresponding to the pipe: DN (mm), NPT, NPS (");4, determine the way to connect with the pipe: flange type, internal (external) thread type, welding type, clamp type, clamp type, card sleeve type, etc.;5, determine the valve operation mode of driving: manual, worm gear drive, pneumatic, electric, hydraulic, electromagnetic, electro hydraulic, etc.;6, confirm the types of valves: gate valve, globe valve, throttle valve, plunger valve, ball valve, butterfly valve, diaphragm valve, plug valve, check valve, safety valve, drain valve, pressure reducing valve and other special valves;7, determine the use of valves: switching type, adjustment type, safety type and so on;8, determine the valve shell and internal parts of the material: carbon steel, alloy steel, stainless steel, ductile iron, gray cast iron, copper alloy, aluminum alloy, plastic and so on;9, determine the valve sealing performance requirements, sealing level or sealing leakage;10, determine the valve coating requirements, packaging requirements, transportation requirements;11, special needs of the valve should also be determined: structure length, valve height, appearance size, flow resistance, emission capacity, flow characteristics, protection level, explosion-proof performance and other parameters;12, determine the valve installation position and posture.

Q:What is the valve?

The definition of a valve "valve" is defined in the fluid system, used to control the direction of the fluid, pressure, flow device. A valve is a device that flows or stops the medium (liquid, gas, powder) in a pipe and equipment and controls its flow. Valve is the control component of pipeline fluid transportation system. It is used to change the passage section and medium flow direction, and has the functions of diversion, cut-off, adjustment, throttling, check, diversion or overflow, pressure relief, etc.. For fluid control valves, valve from the simplest to the most various valves automatic control system used in complex, its many varieties and specifications, the valve nominal diameter from industrial piping and instrumentation valves tiny tolarge diameter 10m valve. The valve can be used for the control of water, steam, oil, gas, mud, all kinds of corrosive medium, liquid metal and radioactive fluid and other types of fluid flow, the valve working pressure from 0.0013MPa to 1000MPa ultra high pressure, working temperature from ultra low temperature to high temperature of 1430 DEG -269. Control valve can be a variety of transmission methods, such as manual, electric, hydraulic, pneumatic, worm gear, electromagnetic dynamic, electromagnetic hydraulic, electric hydraulic, pneumatic and hydraulic, gear, bevel gear drive; in pressure, temperature or other forms of sensor signals under the action according to the requirements. Or do not rely on a simple sensor signals to open or close the valve on the drive or automatic mechanism to make the opening and closing parts for lifting, sliding, rotating or turning motion, thus changing the size of the flow area to achieve its control function.

Q:What is the KVS in the valve parameter?

The Kvs of the valve reflects the passing capacity of the valve

Q:What is the difference between a stop valve (a power station valve) and other valves?

High pressure, special material, complex structure, seldom manual operation.