High Quality Black Annealed Tie Wire

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Black Annealed Tie  Wire

type of hole:round hole/square hole

tensile strength:350N-450N/mm2

elongation:20%

wire diameter:16GA/18GA

packing:3lbs/coil or 3.5lbs/coil

           20coils/carton

Packaging & Delivery

Packaging Detail:in coils
Delivery Detail:25days

Specifications

BLACK ANNEALED WIRE
Black annealed wire is made of high-quality iron wire, mainly used as tie wire or binding wire in construc

BLACK ANNEALED WIRE
Black annealed wire is made of high-quality iron wire, mainly used as tie wire or binding wire in construction work.
We produce the annealed wire with high-quality low carbon raw materials through wire drawing, anneal process. Its soft and has good stretching resistance. The finished products are smeared with slushing oil. So they are not apt to rust. We can tie up the products according to customers requirements, ranged from1 to 50 kg each bundle. And we can also make the annealed wire into U type carbon steel wire, straight cut wire etc. It is mainly used as tie wire or binding wire in construction.
Standard specification: Wire diameter from 0. 229mm-4. 19mm
Packing: Generally inner plastic and outer flax, of course, we can also pack according to our customers' requirements.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do i install flat wire speaker cables?
The flat wire is what you run under carpets, along baseboards, etc. The four wires allow you to run a pair of speaker wires (two sets of two) from your receiver to the general location where the speakers will be. The terminal blocks allow you to run regular speaker wires from the receiver to the flat wire. The terminal block at the other end then lets you run speaker wire from a terminal block at the other end of the flat wire to the pair of speakers that wire feeds. It doesn't matter which wire goes to which speaker, as long as you wire it up correctly. That is, you can have the first terminal be the + wire for the first speaker, the second the - wire for that speaker, and the third and fourth wires being the + and - wires for the second speaker.
Q:ok another pioneer car stereo wiring question?
ILL wire is for illumination. is for the dimmer wire from your aftermarket harness (enables the radio to dim with the rest of the interior lights when you turn your headlights or parking lights on). this wire is not required to be hooked up for the unit to fully operate as some vehicles may not have the proper 12v dimmer wire. The speaker wires that are solid in color (white, Grey, green, purple) are positive (+) and the wires with a solid color and a stripe is negative (-).
Q:Panasonic car radio wiring help?
Honest answer is to take it to a audio specialist. finding and wiring a stereo from scratch (termed hardwiring) is a hard job even for the most advanced audio specialist. This is speaking from experience. Most wires are not colour coded and you will need a amp meter to measure the current, voltage, continuity and resistance in order to find out what wire does what. One wrong wire could mean new speakers or in the worst case set fire to your car. I've have done hardwires for over 5 years, and I've seen some real mess, which quite possibly could have been avoided for a few quid but impatience and inexperience has lead to new cables, trim and other pieces which were damaged due to bad installations. Please be careful!! added 9/11/06: (Note To other answeres) Don't use Choc connections or block connectors for wiring stereos as these are open connections with exposed areas of metal if they came into contact with earthed chassis they can cause a short try using bullet style or butt connectors they are more secure and sheilded!
Q:How do I wire my amp correctly?
wire okorder.com/... and than wire it to any of the negatives on the amp its all one channel internally so it really doesn't matter which negative u use. than wire the positive to any positive on the amp.
Q:How to wire a thermostat to a 220 volt baseboard heater?
That thermostat is a two pole switch. (It opens both lines). Just follow the color codes. Your incoming 'line` might be a two wire run, (Black, White, + Gnd.). In this case just treat that white as a 'Line' wire, (Red). It Should be marked, but sometimes they don't do it. Black, (Line) to Black, T (Stat). Black (T Stat), to Black (Heater). Same for the Reds. The T Stat. should be marked 'Line' 'Load' if it matters with that unit. Some Cautions: 1. Don't try to work it 'live'. 2. If the line wires are black white, be sure that you have a 240V. circuit. -(Two pole breaker). 3. Coil your 'pigtails' (connecting wires), so that the insulation doesn't contact the hot parts of the heater.
Q:Is French Wire Earrings 14kt Gold?
French wire earrings are a style of earrings for pierced ears. They have a long hook shape. They can come in gold or silver or any metal. The style isn't an indication of its metal content. If they are 14k gold, they will need to be stamped as such and you should buy them from a reputable jeweller. Online buying can be a problem, they are people who fake the gold markings (especially goods from Asian countries) and you might think you are getting real gold, but you aren't. Also, sometimes only the wire hook part is gold, the attachment or dangle might be an alloy metal and not gold at all.
Q:Light fixture wiring?
The yellow and green wire is another ground wire. In a house in North America most systems are AC and there is NO positive or negative conductor. The conductors are a ground/bare, white/neutral and any color is a hot wire. The green or yellow green are the exception to the color codes. I suggest you get a book on basic house wiring before you attempt anything besides basic replacement of devices.
Q:Repair headset wire connections?
don't be afraid to cut the wires, those wires are no good, strip out a fresh strand of wire, just make sure you remember the color coding of the contacts before you cut the wires, be warned though, working with earphone wires can be tricky, the solder is very hard to bind on the tips of the wires and the fibers are a pain, if you know how to solder then that's fine, but if you don't ask help from someone who can
Q:how do I wire this up?
Its either red or green,sometimes white if there is a black ground wire.
Q:Bonsai trunk able to grow while it is wired?
Wire it, let it grow a bit. Then, as necessary, undo the wire, then rewire it to fit the new size. An alternative is to append weights, or tie strings to other objects or parts of the plant instead of wiring a whole branch.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range