Specifications1. Horizontal Multistage Centrifugal Water Pump
2. Size: 20mm-32mm
3. Material: SS304
4. High pressure, mechanical seal
- Q:What is the difference between an oil pump and a gear pump?
- Two different concepts, also has oil pump gear type oil pump, divided into two categories: rotor and gear type; the concept of gear pump is wide, many pumps are used in gear, so your answer is: they cannot be compared, but the relative type oil pump gear some good. Satisfaction please accept, thank you
- Q:The car oil pump is broken. What are the problems?
- There's no trouble. You're not going straight
- Q:What is the influence of insufficient oil supply in the oil pump?
- Tank or pipeline bubbles; hydraulic system from "Ji, Ji" sound to ascend; the tractor has just started working device can improve the elevated temperature after a period of work, ascension is slow or not to upgrade; light load can improve, can enhance the expansion stage heavy load.Failure cause:(1) hydraulic tank oil level is too low;(2) do not use hydraulic oil according to season;(3) the tubing is seriously blocked by dirt;(4) the gear oil seal of the oil pump is damaged, and the air enters the hydraulic system;(5) the oil pump inlet, outlet port or bent joint "O" shaped sealing ring is damaged. The fastening bolt of the bending joint or the inlet and outlet pipe nut are not tightened, and the air enters the hydraulic system;(6) the inner leakage of the oil pump and the aging of the sealing ring;(7) oil pump end face or main or driven gear sleeve end face wear or scratch, two axle sleeve end surface roughness is over bad;(8) internal assembly error of oil pump causes internal leakage;(9) "left hand" installed "right" oil pump, causing the impact of the skeleton oil seal;(10) hydraulic oil is dirty.
- Q:What are the fuel pump inspection items for diesel generator sets?
- The 1. check valve plane if worn, sag, such as pitting phenomenon, application of grinding paste on the plate grinding, severe cases should be renewed.2. of the one-way valve seat surface wear serious or not smooth, should be replaced.3., the top rod and the top sleeve wear seriously, so that the gap increases, the seal becomes worse, the diesel oil leak seriously, then need to replace with the shell, or choose the enlarged size of the top pole, but need to pass the mutual research.The coarse strainer core 4. oil inlet pipe joint, and easy to be cottony sundries plug, effect of fuel supply, it should always pay attention to the clean fuel and remove the dirt on the filter core.5. hand oil pump piston rubber ring damaged, should be replaced in good time. After the center of gravity of the oil pump is assembled, the moving parts of the piston, the ejector rod and the other parts of the oil pump are required to be in good motion during the whole journey, and no blocking and blocking are allowed. The hand pump should be light and flexible. Pay attention to the installation of the one-way valve spring. The check valve spring must be accurately embedded in the spring slot.
- Q:Automobile oil pump fault
- Such a problem can arise. The oil pressure is too high, and the oil filter is opened by "drum". The reason is that the oil pump pressure limiting valve [pressure relief valve], resulting in a failure, can not normally open at high pressure caused by pressure relief
- Q:How to repair the Iveco oil pump
- Iveco oil pump driving wheel how down have special tools for heating 200 degrees
- Q:How can Honda know when the pump is broken?
- Hello, check whether the oil circulation, steel cap is on the oil, I hope my answer can help you, I wish you a happy car!!
- Q:SUZUKI motorcycle oil pump is not on the oil, the circuit is not blocked, to replace the oil pump
- Is the oil filter and the oil filter plugged? Is the filter core apron missing? How do you make sure there's no blockage? No reason for the oil is only the oil pump damage, filter, filter or oil clogged, lack of oil and several other reasons.
- Q:Does the abnormal sound of Audi Q5 oil pump need replacing?
- If it is the oil bar, if there is a sound, the abnormal sound must be replaced, this is beyond doubt. I hope my answer can help you
- Q:The function of the oil pump screen is troublesome
- The function of the filter is to filter the impurities in the oil
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average