Gypsum Board in Size 2400*1200*15mm for Partition

Ref Price:
Loading Port:
Qingdao
Payment Terms:
TT OR LC
Min Order Qty:
600 pc
Supply Capability:
120000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Main Material: Gypsum Powder

Normal size: 2440x1220mm, 2400x1200mm

Normal thickness: 7, 8, 8.5, 9, 9.5,10, 12, 13, 15mm

Edge: Square, Tappered

Category: Regular, Fire resistant, Moistureresistant, Water proof

Performance: Fire-resistance, Moisture-resistance,Water-proof, Heat-preventing


Specifications:

1) Sepcial healthy breath function

2) Cost effective and more reliable, easy to install

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What insulation should i use to fill between the joists of my house before i replace the plasterboard ceiling?
Polyisocyanurate insulation.
Q:How to deal with damp/wet skirting boards that are attached to plasterboard?
Those skirting boards as you call them were originally installed to act as a support for when the plasterers floated out the walls with plaster. You can go ahead and replace whatever is bad with new boards. The plaster will not fall off the wall, when you do this. You are fine! Understand that pre-1978 buildings with plaster have asbestos fibers in them. They are know to cause cancer. You need to specially CONTAIN the area and were special protection when doing this work. DO NOT CONTAMINATE OTHER AREAS OF THE HOUSE.
Q:What is the material gypsum board scraping white?
Now the wall decoration, including scraping and latex paint, the former is a simple decoration cheap but the effect is not good, the latter price is relatively high but the effect is very good, the former material needs putty, which requires special putty and latex paint. program: View the wall with no gaps, such as the wall on the mouth, gypsum board shape gypsum line. If there is a gap, first filled with gypsum and then brush the white latex glue bandage. View the wall with or without rust [nail steel head] If so, use the machine and then make up the plaster. (Scraping gypsum). 【Note: all the roofs of the house must be full of gypsum, because the ceiling shovel out after the very uneven] can not directly scraping white. Gypsum and big white are very different. Before the scratch, the work of gypsum is: all paste the bandages, gypsum board, cement surface. Have to scratch the gypsum. (Scraping white). It is important to draw at least twice. The first pass to be scratched, do not have missed the. The first time to finish, to check the roof and the wall with or without rust. Whipped the second time. After the white finish, to ventilation, do not boring like a wind window can open for a while off, different weather different treatment (White after the dry dry sandpaper). 【Polishing is a brush [spray] latex paint must be done before work. But at the same time polished sandpaper is a very important part of scraping white. The construction workers in the scraping of the white sweep of the scraper of the Road purlin small packets have all worn away. (Protected). So that latex paint stained with bad rub. Brush latex paint. [Note: The above is the main program of scraping white. "Good white" also need other targeted "procedures".
Q:What paper is used for paper gypsum board
The country's largest gypsum board production line, North New, with the Zaozhuang Tengzhou plateboard
Q:The room to do a gypsum board ceiling, top what to do?
If you want to do the ceiling, the original top do not need to do any treatment, sweep clean on the line.
Q:Gypsum board partition and brick wall connection, how to build to achieve no cracks
To ensure that the most reliable is covered with a steel mesh shop
Q:How do I plaster board?
It needs to be attached to the walls with screws or nails. You should be using concrete board for tiling over a wall.
Q:is it safe to run a power cord behind a plasterboard wall?
Not advisiable..... I had a house fire once because of an electrical wire behind a wall that burnt my whole kitchen down. I was lucky to get out alive.
Q:Gypsum board belongs to what product category
Gypsum board is a kind of material made of building gypsum as the main raw material. It is a light weight, high strength, thinner thickness, easy processing and insulation and fire insulation and other good performance of the building materials, is currently focused on the development of one of the new lightweight sheet
Q:Is plasterboard finish really any good?
sounds like the screws were not properly set or sealed to begin with- probley just poor workmanship. Just so ya know after the screws are put in they need to be sunk in a bit with some pressure - then sealed with mud or patch. I would guess your contractor did that already. ? and are you sure they used screws? i only ask cause sometimes nails are used and they pop causing the problems you mentioned- but the right screw is used it is uncommon that would happen. If you live in a moist area where there is high humidity - it is possible that the plasterboard has expanded a bit pushing the screws out- you can have the humidty levels checked - or you can probley feel if there is excess moisture in the room and maybe that can be cleared up with good ventilation. It is also possible they did not use a long enough screw, or the beam was not hit when it was screwed in- if thats the case then there probley is no remedy except basicly removing all the screws and repositioning them.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range