Gypsum Board in Size 2400*1200*13mm for Partition

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
700 pc
Supply Capability:
120000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Main Material: Gypsum Powder

Normal size: 2440x1220mm, 2400x1200mm

Normal thickness: 7, 8, 8.5, 9, 9.5,10, 12, 13, 15mm

Edge: Square, Tappered

Category: Regular, Fire resistant, Moistureresistant, Water proof

Performance: Fire-resistance, Moisture-resistance,Water-proof, Heat-preventing


1) Sepcial healthy breath function

2) Cost effective and more reliable, easy to install

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Wallpapering on to a chipboard wall not plasterboard?
Q:can i put 8ft by 4ft plasterboards on a ceiling?
Of course you can.... 1/2 thick is recommended.... Are you going over an existing ceiling? is this new construction..need more information.... Perhaps you ask cuz the room is larger than 8' wide....It would be better to have full lengths wall to wall, but not necessary, just a bit harder to tape. but this is done on most ceilings. If you can get longer sheets, it would make for a better job, but perhaps, it is not possible to fit the longer sheets into the space.... To avoid the expense of a drywall lift, make t-heads about an inch longer than the ceiling ht, and use them to hold up the sheet while you screw....have a make the job run smoother
Q:Gypsum board hanging end need to brush latex paint it
Gypsum board ceiling finished sure to brush latex paint. Gypsum board ceiling after there are three processes, the first step point anti-rust paint, because the nail if you do not have anti-rust paint treatment will rust and yellow. The second is the batch of putty, because the gypsum board ceiling surface is not very flat. The third step is to paint latex paint!
Q:is it possible to dot n dab plasterboard over painted pebble it is inside a new extension its solid and would?
no problem karl ..done it many times ..pva the wall with a roller first and off you go ...
Q:how to measure jobs off plans for plasterboard?
Plasterboard/ sheetrock comes in 4x8 & 4x12 ft sheets 1/2 to 3/4 inch thick.. 4x12s are usually railroaded ( applied horizontally) but are heavy & harder to handle in small residential spaces. Also take into account doubling up if the plans call for fire rated walls or clgs in furnace enclosures or attached garage space. Measure each individual wall surface to the scale of the drawing or pick off written dimensions & divide by 4 if applying vertically in an area w/ an 8 ft clg. Eg a 12 x will need 14 sheets for walls & 6 sheets for clg. 1/2 thick or better for walls & 3/4 for clgs Wall length total ..12+12+16+16= 56 ft divided by 4= 14 Ceiling area .12x 16= 192 sq ft ( area of ech 4x8 =32sq ft) 192 divided by 32 = 6 In residential construction door & window openings are not figured in unless they are very wide & tall. Measuring too closely can cause you to run short esp if a wall dimensions run out greater than even multiples of 4 & you can consider anything over to be a full sheet & use the cutoff in another space. Your supplier can give est on taping compound , joint tape & fasteners based on your order. Wall & clg sq footage is also used to est paint . wallcovering & floor covering requirements Best regards
Q:Living room to do gypsum board ceiling what materials
Wood keel, gypsum board, gypsum board screws. Floor nails
Q:Do you use a gypsum board to make a wall that is neither strong nor clean?
Gypsum board can generally do partition, sound insulation is very good. And the construction is convenient. But the wall can not hang something only. When the wall is made, it is usually pre-installed keel frame, and then the gypsum board installed on the keel, and then paint or paste wallpaper, and the concrete wall looks no different. As long as the keel is strong, then the gypsum wall is very strong. However, because the essence of gypsum hard, but not suitable for hanging in the above things, so similar to the frame painting is not suitable for direct suspension, unless you find the keel, nail on the keel above Caixing. If there is no hanging weight, then the gypsum wall is still very practical.
Q:The difference between MDF and gypsum board
The difference between MDF and gypsum board - MDF features. Advantages: uniform density, easy processing, you can do carving, you can paste a variety of veneer and decorative panels on the surface. Hard density board by punching, drilling, can also be made of sound-absorbing panels. Disadvantages: the biggest drawback is poor water resistance, water swelling rate is large, easy to deformation; grip screw force difference; with plastic volume, with the glue is not good, the seal work is not good, then formaldehyde release will be relatively large. The difference between MDF and gypsum board - the characteristics of gypsum board. Advantages: moisture, fire, breathable, and construction is simple. Disadvantages: difficult to deal with the gap, easy to crack, no noise, no insulation (can be added asbestos solution), wall vulnerability and so on.
Q:whats the difference between gypsumboard and plasterboard?
Plaster board is water resistant. Gypsum board is regular sheetrock and needs to be taped with join compound as apposed to plaster.
Q:How to install the ceiling gypsum board

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range