Order On-line Tracking
Features & Benefits of GRP FRP Equal Tees Sea Water Pipe Series
•Long, effective service-life materials
•No need for linings, coatings, cathodic protection, wraps or other forms of corrosion protection
•Low maintenance costs
•Hydraulic characteristics essentially constant over time
(1/4 weight of ductile iron; 1/10 weight of concrete)
•Low transport costs (nestable)
•Eliminates need for expensive pipe handling equipment
Long standard lengths
(6, 12 metres)
•Fewer joints reduce installation time
•More pipe per transport vehicle means lower delivery costs
Extremely smooth bore
•Low friction loss means less pumping energy needed and lower operating costs
•Minimum slime build-up can help lower cleaning costs
With elastomeric rubber rings
•Tight, efficient joints designed for bell & spigot to eliminate infiltration and ex-filtration
•Ease of joining, reducing installation time
• Accommodates small changes in line direction without fittings or differential settlement
•Custom diameters can be process manufactured to provide maximum flow volumes with ease of installation for rehabilitation
High technology pipe design
•Lower wave celerity than other piping materials can mean less cost when designing for surge and water hammer pressures
High technology pipe manufacturing system producing pipe that complies to stringent performance standards (AWWA, ASTM, DIN, EN, etc.)
•High and consistent product quality worldwide which ensures reliable product performance
Control Testing of GRP FRP Equal Tees Sea Water Pipe Series
Raw materials are delivered with vendor certification demonstrating their compliance with Zhongfu Lianzhong quality requirements. In addition, all raw materials are sample tested prior to their use. These tests ensure that the pipe materials comply with the specifications as stated
The manufactured pipe’s hoop and axial load capacities are verified on a routine basis. In addition, pipe construction and composition are confirmed.
All pipes are subjected to the following control checks:
• Visual inspection
• Barcol hardness
• Wall thickness
• Section length
• Hydrostatic leak tightness test to 1.5 rated pressure (only PN6 and above)
On a sampling basis, the following control checks are performed:
• Pipe stiffness
• Deflection without damage or structural failure
• Axial and circumferential tensile load capacity
Model of GRP FRP Equal Tees Sea Water Pipe Series
Unloading，Handling，Transportation and Storage of GRP FRP Equal Tees Sea Water Pipe Series
Unloading the pipe is the responsibility of the customer. Be sure to maintain control of the pipe during unloading. Guide ropes attached to pipes or packages will enable easy manual control when lifting and handling. Do not drop, impact, or bump the pipe, particularly at pipe ends.
If at any time during handling or installation of the pipe, any damage such as a gouge, crack or facture occurs, the pipe should be repaired before the section is installed.
Strap pipe to the vehicle over the support points using pliable straps or rope. Never use steel cables or chains without adequate padding to protect the pipe from abrasion. Bulges, flat areas or other abrupt changes of curvature are not permitted. Transport of pipes outside of these limitations may result in damage to the pipes.
Site Pipe Storage
It is generally advantageous to store pipe on flat timber to facilitate placement and removal of lifting slings
around the pipe.
When storing pipe directly on the ground, be sure that the area is relatively flat and free of rocks and other
potentially damaging debris. Placing the pipe on mounds of backfill material has been found to be an effective
way of site storing the pipe. All pipes should be chocked to prevent rolling in high winds.
FAQ of GRP FRP Equal Tees Sea Water Pipe Series
Q1: What’s the performance standards?
Lianzhong pipe is designed to meet all of these ASTM , AWWA, BS, DIN standards.
Q2: What’s the qualification testing for the products?
Lianzhong pipe has been rigorously tested to verify conformance to the ASTM D3262, ASTM D3517, AWWA C950 and DIN 16868 requirements
Q3: How long can I receive my goods?
A: Usually, we will deliver products within 20 days after the contract is signed. Delivery time is negotiable when necessary.
1. Manufacturer Overview
|Annual Output Value|
2. Manufacturer Certificates
|a) Certification Name|
3. Manufacturer Capability
|No.of Employees in Trade Department|
|No. of Production Lines|
|Product Price Range|