Q:Hello, I would like to consult the power between the conveyor and the motor is the same Mody, is not the conversion of the formula is what ah, thank you

No. The power of the motor is generally easy to calculate by the current and voltage, but the power of the conveyor is mainly between the friction between the object and the conveyor and the speed of movement. For example, if the level of the conveyor belt, the object is uniform when the conveyor belt is no power

Q:What is the motor used in the pipeline in the factory? Above also equipped with a reducer, you can adjust the speed of the motor, this motor is what motor? What is the general model? How can we buy the right motor? I do not know what type of motor to buy ////////////////////////////////// more

Generally speed motor, frequency control

Q:Single mouth Ma machine conveyor belt broken, but do not know how to put the conveyor back more

Remove the two screws from the trough and put the belt in. Note that the tightening wheel below will be put right, and the belt will be loose.

Q:The motor has a fixed diameter wheel, connecting the conveyor belt. Conveyor belt with a large round of walking slow, or with a little bit of the wheel to go slow?

The same reason, the small wheel when pulling the big wheel of the motor power to torque, so the case of the same speed, the small wheel with a large wheel faster, on the contrary, the big wheel to drag the ferry, the motor turn fast , While the ferry was pulled by the conveyor belt, the ratio should be 2: 1, that is, the motor with two horsepower, the wheels only to accept a match

Q:What is the reason why the tunnel conveyor belt does not move

Thank you feeling that this question is meaningless or find their own information under it

Q:To design a conveyor belt, 2 m / min, 3 m long, used to send the PCB board, very light, that is, do not know the choice of the motor, what about the power, and the wheel is not casually size, , The motor to add the inverter, or gear motor, or electronic regulator? Which is more suitable, why? Can you tell me Do not copy some online have to perfunctory! Thank you! More

Speed belt belt / drive the best, the roller can be added 3 ¤ 10mm (short), the electronic governor has not been able to tune 3 phase, 1.5KW motor is enough, of course, but also control the electrical leakage, Open,

Q:I have two sets of conveyor belt, cylinder and air compressor, the trachea are connected. The existing JS14P time relay 1, CJX2-1210 contactor 2, are AC220V, diffuse photoelectric switch 1 [2 lines often open 220V], how to wiring? Puzzled line of their own, but there is a contactor will be baffled, how to solve, how to properly wiring. Urgent thanks! Question added: I would like to ask which master can draw a picture really thank the younger brother

If your metal parts are not long enough, when the photoelectric switch receives the signal to start the timer, you also need to add a self-locking loop, so that time relay can be time.

Q:The factory made a 2-meter-long small conveyor belt, do not know what kind of motor and control? The motor starts to stop frequently, the minimum 1 second time, with a signal to control the conveyor belt to stop, and stop when the request to stop immediately, are not allowed to inertia. More

With the power of the brake motor can do "stop", but the frequent start of the motor is a test. If possible, add a clutch between the gear unit and the conveyor belt, and add an electromagnetic brake to the input shaft of the conveyor. When the clutch is closed (the electromagnetic brake is also released), the conveyor moves; when the clutch is disengaged (The electromagnetic brake is also tensioned) The conveyor belt stops. Use control of the clutch and brake to control the movement or stop of the conveyor belt. While the motor is in continuous operation. Another solution: If you need to use the transport distance as a conveyor belt based on the start, you can use pneumatic system to achieve their goals. Feed with cylinder (2 sec.) And return quickly (1 sec.). To avoid the problem of frequent start and stop the motor.

Q:If there is a conveyor belt, use a smaller force to push the gear so that the other side of the larger force of the gear rotation

With a semi-crossed drive, so small pinion force

Q:My automatic mahjong table conveyor belt how to reverse the motor, it should be up to send the card, and now it will pass down the card, resulting in the card simply do not get on, the magnetic circles suck the cards are gone, Do not say anything more

Have you ever been repaired? According to what you said, I made a look at the analysis, please refer to: First, as the first floor said, continued electrical (capacitor) is broken, you can change a high-power, but the motor will have some sound, can barely use. Or directly replace the motor Second, the conveyor belt dirty, mahjong table conveyor belt motor with a reverse function, if the belt is dirty, forward belt does not move, it leads to reverse. You can spray Billy beads on top of the belt to try, it is best to wash mahjong. Third, the motherboard is broken, it is more complex, motherboard circuit problems, according to the brand you buy, find manufacturers to replace the general warranty. Fourth, K4 light sensor for, resulting in not read the card, paint about the light, that is, on the licensing device, there are two small bulb-style stuff. You can also adjust its sensitivity to try. Fifth, the mahjong table this stuff, fear of tide, pay attention to keep dry. Sixth, if the above method no longer, mahjong table with automatic detection file, you can adjust to the detection file, automatic detection, according to the instructions. If not, it is best to find a professional. This is my personal point of maintenance experience, hoping to help you. for reference only.