Q:How to replace the basin hot and cold faucet hose

Prepare the tools: raw material belt, adjustable wrench, hot and cold water pipe (length according to your actual situation, that is, the basin from the hot and cold water connection at the distance.First, the total water valve off, Let go of the pool of water, so easy to connect the water at the head of the connection, or hand is not stretched out, the old water pipe removed in the connection of the hot and cold water interface at the link Material, at least around 15 laps, then the hot and cold water pipe connected to the first hand twist, do not move after the wrench, to feel some tight on it.

Q:8-inch faucet basin basin can hold 4-inch faucet you do

Can be installed, but a little loose, so the basin basin up and down to install a 4-inch hole with a rubber gasket, the middle also clip an 8-inch diameter, 4-hole hole, the thickness of the basin and the equivalent of Gasket, so that the faucet can be just in the 8-inch hole in the central position.

Q:The faucets are Kohler faucets and they are probably not brass but are brass colored. Any suggestions you might have will be appreciated.

if you aren't sure if it actually is brass i'm not sure how well of a job it will do in polishing it. Basically most polishes work by rubbing off the oxide that has formed. I'm not sure how brasso wil react with non-brass metals, the same way iwouldn't polish sterling silver with brasso. if anything might i suggest some sort of home concoction? I Think vinegar was something peoples used as polishing. It has an acidic property to help remove the oxide, but no chemicals to worry about that might mingle with the metal. I don't recall what else they mix with the vinegar. You can just google "home made polish" I'm sure it'llg ive you a list of them Well good luck with your fixtures.

Q:Kitchen basin basin faucet down how to repair

Look at the leading buds and nuts have broken off? Not broken is the faucet and the bottom of the basin at the bottom of the faucet nut tightened just fine

Q:Basin faucet leaking, how to disassemble?

The interface rust is difficult to remove: the bathroom faucet in the demolition, at least into the water pipe connection is easy to separate. The kitchen, whether it is the water inlet or faucet with the table connection, the two interfaces are difficult to unscrew.

Q:Want to wash your hair in the basin, but the leader is too low, how to do it?

Haha and I used a habit, there is brushing, do not want to use the cup directly to the leader to drink water mouthwash, I bought the kind of glass basin with the high pole of the lead, very convenient.

Q:Is the basin faucet to the angle valve?

Hot and cold water, then two angle valve, a single cold on a corner valve. To install the angle valve, then buy a good point, do not lead no bad, angle valve first bad, it would be better not installed.

Q:I was filling a large basin with hot water. Suddenly there was a 'thump' and the water stopped running. I pushed the handle back and got cold water, then to the right and got cold water. But when I pushed the handle all the way to the left to get hot water, no water came out at all. The bathroom faucet gives hot water when I turn the handle and the bath faucet gives hot water. What happened to my kitchen faucet?

Sounds like you need a new cartrige in your faucet. Usualy not a hard fix. turn off water to hot and cold underneath faucet, remove handle and faucet parts untill the valve is free. then replace. Google the faucet you have and you should finde a vidio on how to do it.

Q:Is it necessary to use a corner valve below the basin faucet? What is the role?

With the angle valve is easy to replace the faucet in the future, if the faucet is broken, can turn off the water in time, you can also adjust the water pressure of the faucet.

Q:What brand of basin is good?

I use the eagle bathroom, aftermarket is better, you can help repair