our brass tee fittings has followings features
2) Very slow size error(below 0.1mm)
3) Higher warranty
4) double ferrule structure make sealing function better
5) long warranty
45, 60, 90 degree are available
CA360 OR CA 377(H59, H60)
operating temperature: below 150 degree
applicable pressure: 1.0_16Mpa
small orders(below 8000PCS) will be finished within 20days
Larger order will be sure accord our aggrement.
- Q:Can the sleeve type pipe joint be disassembled and assembled several times?
- The European and American card sleeve pipe joint is a standard part, it can be disassembled and assembled many times, but it is better to check the sealing cone into the pipe, whether the inner component has the wrong face, the pipe is better to choose the new connection.
- Q:Plastic pipe joint leakage, how to deal with better?
- Repair seal.Specific operation, see the following points:Now that the water leaks, you'll find the main switch for this pipe and turn it off for later maintenance;
- Q:Do you need adhesive for the sleeve joint of PVC wire pipe?
- It is, in theory, but very rarely used. Wiring can be done without adhesive.
- Q:Press the hydraulic pipe fittings standard need to do what procedures
- Press with 19mm four layer steel wire hose (Italy Manul manuli4sp) from the hydraulic tubing buckling parameters in the table look up with four layers of 19mm steel wire hose joint diameter is 37mm before pressing coat, rubber 33.5mm, the die diameter is phi 33mm,
- Q:What are the sealing ways of pipe joints? Thank you
- The pipe joint is the connecting tool between the pipe and the pipe, and it is the connection point between the component and the pipe. It plays an indispensable role in pipe fittings. It is one of the two main components of hydraulic pipe. The pipe joint is used for straight connection such as instrument, and the connection forms are socket welding or threaded connection. It is mainly used in low pressure pipes with small diameter, used for parts that need to be packed frequently or used as final adjustment of threaded pipe fittings. Fast and easy and related products were included, should adopt the structure of metal surface contact sealing structure, structure of gasket seal is usually used for conveying water, oil, air and other general pipeline, the use of malleable cast iron material. In addition, the use of requirements and prices are also factors to consider when selecting.
- Q:New standard, how can the pipe joint be labeled, such as "3/4" taper pipe thread?
- The English system is 55 degrees of thread, and the internal thread of taper pipe is Rc3/4. The outer thread is R3/4The U.S. is 60 degrees
- Q:Apart from the air-conditioning, the high-pressure pipe is not tight enough. What shall I do?
- If the connection is not tight, is the copper pipe joint cracked or deformed?
- Q:Air conditioning pipe joints how to remove, the joint is ring, there are similar to the spring on the oil seal
- 2. Disassemble the outdoor machine copper pipe joint and disconnect the outdoor mechanical and electrical connector (remember the order of the lines).3. Remove the indoor and outdoor units.
- Q:The material is 304 stainless steel 1/4 "NPT" threaded joint. How much MPa pressure can be received?
- I've seen a lot of discussion about the NPT thread's stress levels, and none of them are accurate.He who knows knows not to answer. It took time to find relevant global requirements. For your reference
- Q:What joints do nylon hard tubes work on?
- (I) flared type pipe jointApplication: oil, water, gas and other non corrosive or corrosive medium pipe joint with steel pipe specifications and flexible pipe welding, has the characteristics of reliable connection, good sealing performance, so it is widely used in oil refining, chemical industry, light industry, textile, metallurgy, national defense, aviation, ship etc.; also suitable for hydraulic transmission of various mechanical engineering, machine tools and other equipment pipeline. Flared tube fittings are manufactured in the following six categories:
We insist on the business philosophy of "quality standard coexists with the enterprise and market and honor be first", and sell products to relevant overseas companies. We have received honors given by our customers at home and abroad.We are looking forward to your visit and the pleasure to process according to your samples and drawings.
1. Manufacturer Overview
||Zhejiang, China (Mainland)
|Annual Output Value
||US$5 Million - US$10 Million
||Quality Management System Certification
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||31% - 40%
|No.of Employees in Trade Department
||English, Chinese, Spanish, Japanese, German, Arabic, French, Russian, Korean, Italian
||5,000-10,000 square meters
|No. of Production Lines
||OEM Service Offered Buyer Label Offered
|Product Price Range