Gate Valve Flange Competitive Price Made in China

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
200 m.t.
Supply Capability:
10000 m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Item specifice:

Material: Cast Iron Pressure: High Pressure Temperature of Media: Normal Temperature
Power: Manual Media: Water OD(Outer Diameter: inch): 210
Size(inch): DN125 Pressure(LB): 250 Net Weight (kg): 44

Product Description:

1.Structure of Gate Valve Description:
Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow.

2.Main Features of the Gate Valve:
• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber
•  Free of water pollution
• High manufacturing accuracy
• High strength
• Environmental protection and energy saving
• Good visual effect
1. We offer the non-standard valves,according to customer requirements
2.If you want,you can have your own logo on the products
3.Export to mainly market: Russia and America
4.We can promise the quality

3.Images of the Gate Valve
 Gate Valve Flange Competitive Price Made in ChinaGate Valve Flange Competitive Price Made in China

4.Specification of the Gate valve
(1)Forged Brass Screw Gate Valve, Brass valve, Brass Gate Valve
(2)Forged body, cast iron handle
(3)Can be changed to allum. handle
(4)Cast Iron Wheel Handle, can be changed to allum. handle
(5)Screw Ended
(6)Material: CW614N, CW617N, C37700 as per request.
(7)Thread: BSP, NPT as per request
(8)Marking: Can marked be as per request.
(9)100% Pressure Tested.
5.FAQ
1. What's are the characteristics of gate valve?
The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel.
2. What is the work principle of gate valve ?
The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry.
3.  What is the structure?
Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How can the material be checked by valve approach? What experiments do you need?
(8) the throttle valve does not test the tightness of the closing parts, but the strength test and the tightness test of the stuffing and the gasket shall be carried out.(9) the pressure test, the valve closing force only allows a person's normal physical strength to close; not augmented with tools like leverage (except torque wrench), when the hand wheel diameter is greater than the wait at 320mm, allowing two common off.(10) with a sealed valve, should be taken out of packing for sealing test, sealed after the official closed, check whether leakage. When gas is used as a test, check the water in the stuffing box. When sealing test is carried out, the upper seal is not allowed to be in the tight position.(11) when the valve with drive device is tested and its tightness is tested, the sealing test shall be carried out by using the driving device to close the valve. For manual drive units, seal test shall also be done with the actuating closing valve.(12) the by-pass valve installed on the main valve after the strength test and the sealing test. The strength and tightness test of the main valve is carried out. The main valve should be opened when the closing member is opened.(13) iron valve strength test, the application of Pratia tapping valve and valve cover, check whether there is any leakage.(14) the valve test, in addition to the provisions of the plug valve to allow sealing surface oiling, other valves are not allowed in the sealing surface of the oil test.(15) when the valve pressure test, the blind plate on the valve pressure should not be too large, so as to avoid deformation of the valve, affecting the test results (cast iron valve if pressed too tight, will be damaged).(16) after the valve test pressure, should promptly remove the water and clean the valve, should also be prepared for the test record.
Q:What do you mean by "P54" in the valve z962y-p54 100V?
Applicable temperature 540 degrees centigrade;Applicable temperature 540 degrees centigrade
Q:The valve is rusty and can not be opened. What shall I do?
Spray with rust removing agent on the rusty rotating parts of the valve. Then use an afterburner to make a tentative rotation. Open it and turn it in the opposite direction. And then spray rust remover. Repeat this several times, and the valve will probably open. Seriously rusty valve, if it really can not open, simply replace it.
Q:How to check if the gas valve is open?
The gas valve has a handle, and the handle is parallel to the pipe and is opened, and the vertical is closed. If there is no handle, there is a rectangular main handle on the valve, the principle is the same as above.
Q:How does the valve rust die?
The treatment of valve rust is as follows:1, use corner grinder cut off valve, and then a small mill grinding wheel cutting residual film cut pipe installed in the screw part, when the attention of cutting depth.2, with the amount of hydrochloric acid corrosion and rust of the valve, until the rust completely removed, rinse with water.3, on the newly purchased valve galvanized, can effectively prevent rust.Valve (Famen) is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure. Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow.
Q:Can the angle valve of York central air conditioner be replaced by other valves?
Definitely. But I want you to tell me what you're doing, or give me a picture. I can give you some advice
Q:What are the valves at home?
Valve used in the family is commonly used, the following are several:On the water pipe are: total table of the ball valve (32mm), in charge of the (25mm), as well as for the toilet, washbasin, water heater angle valve (20mm).Other commonly used gas pipelines, valves, pressure reducing valves and the like.
Q:What does valve A335P22 mean?
The first seems to refer to the material inside the valve, containing Cr of 13% (equivalent to the 1Cr13 of our country), FHF=full face hardThe other refers to the body of the material, the corresponding standard forWC6=ASTM A217 WC6P280GH=EN10222 P280GHA335P22=ASTM A335 P22
Q:What do O and S mean on the valve?
Generally used in process valves, operating conditions required to open and close, especially in the case of pneumatic actuators installed, the loss of power and gas supply valve when the state
Q:What valves are needed on the construction site?
Order valve flow1, customers have special requirements for products, must provide the following instructions in the contract: a) b) the length of the structure connection form C) nominal diameter, full size, shrinkage, pipe size d) using medium and temperature and pressure range E) test, inspection standards and other requirements.2, the factory can be configured according to customer specific requirements of various driving devices.3. If the customer provides the type and model of the valve to be determined, the customer shall correctly explain the meaning and requirements of the model and sign the contract on the condition that both the supply and demand sides agree.4, futures, order customers, please call the letter in detail to tell you the required valve model, specifications, quantity and delivery time, location, factory information, billing information, delivery address. And in accordance with the total amount of 20% of the predetermined amount or full amount of money, timely import our factory account, and the rest of the payment before shipment, import, in order to arrange delivery in time.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range