Gas Safety/Gas Solenoid Valve/Flange Solenoid Valve

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
50 Sets set
Supply Capability:
1200 Tons Per Month set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

‍Packaging & Delivery
Packaging Details: free fumigation plywood case or as buyers' requirements.
Delivery Detail: decision in consuctation with customers according our practical

 

Specifications of Applicable medium: gas,natural gas,LPG. 

Body matenal : Die-casting aluminium.

Protection degree: IP54. 

 

Technical specification


Categoriesofcontrol:directly drive


Applicable medium:gas,naturalgas,LPG


Structure:diaphragm seal valveseat


Maximum working pressure:0.2MPa


Nominal pressure:PN16


Connection:Female screw/flange


Voltage:AC220V/50HzDC24V


Close time:<1S(about 20 msec)


Protection degree:IP54.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What's wrong with the sealing ring at the needle valve of the spray gun?
If the sealing ring break not leak does not affect the pressure, spray a shares is because the last time you painted not wash or spray gun, the valve needle sharp deformation, if often run out of the gun after cleaning will cause the spraying effect is not good, long lance clog, preferably after use with clean water that day!
Q:Needle valve hot runner outlet hole shrink what is the reason?
Because the valve needle is into the gate, the hot runner temperature here is the highest, so the plastic temperature near here is the highest. The higher the temperature is, the greater the shrinkage, so when the product is cooled naturally, the needle valve has the largest shrinkage hole.
Q:If the material selection is not appropriate, long time production, will cause wear of the valve needle, some suppliers use inferior needle valve, or valve needle without cutting, non professional technology, can easily lead to the valve needle top is not smooth, resulting in gate galling phenomenon, the effect is not good, the final effect the quality of products. I hope I can help you
That's what it says. It depends on the material you formed, but I think it's safer in the 0.3 wire.
Q:Hot runner mold valve needle sealing is lax, what are the reasons?
The main reason is that the cylinder pressure is not enough. Two the injection quantity over three, low temperature hot nozzle, four valve seal leakage, valve needle valve needle sleeve wear Arno, wear after lead carbide glue leakage valve needle movement is not in place, the size of the mold is not precision.
Q:How does a sequential needle valve work in a hot runner?
According to the signal issued by the injection molding machine to control the solenoid valve switch, the current hot runner integrated timing controller, the price is good, easy to use
Q:How many times can the hot runner valve needle be used?
Needle valve has good or bad, generally have quality requirements of the needle valve, the basic use of the industry standard disk needle valve, the international standard moldThe valve needle surface hardness of HRC60-62, titanium, with non stick material, high abrasion resistance, continuous use up to 1 million times,
Q:What is the hot runner valve needle?
There are DME (USA), INCOE (USA), MOLD-MASTER (Canada - hot runner), HUSKY (Canada) and so on
Q:How to use the needle type oil cup
Method of use: D needle type oil cup is a cup, the cup is a middle upper lid, from the top to the bottom through a needle valve, the cup cover is bending spring, pressure spring pressure to the middle of the adjusting nut adjusting nut to adjust the valve pin to the top of the lower end of the oil outlet open the upper part, and sideways to erect it can put the valve open to the maximum.
Q:Hot runner valve needle in the molding, why will retreat?
It should be molded and sealed with glue.
Q:Is the injection pressure tight after the valve pin closes?
In the process of injection molding, solution and shrinkage because of cooling, but because the screw to move slowly forward, so that the material in the tube to melt into the cavity, to supplement the needs of shrinkage, called pressure. It means to prevent product shrinkage, with pressure if production is stable. The pressure can also adjust the product size, without weld line
Product range: (1)Valves:gate valve,check valve,globe valve,ball valve,butterfly valve,control valve,safety valve,angle valve,Titanium alloy valve, thermostatic valve,needle valve,plug valve,etc. (2)Flanges and Pipe fittings:all kinds of flanges,elbow,tee,caps,union,plug,coupling,reducer,etc. (3)Pumps:Sewage pump,sand suction pump,centrifugal pump, mixed flow pump,hand press pump,self- priming pump,etc.(4)Faucet:ABS shower head,LED shower faucet,kitchen faucet,basin faucet,etc. (5)Small brass valve:ball valve,angle valve,etc.

1. Manufacturer Overview

Location Beijing,China (Mainland)
Year Established 2003
Annual Output Value
Main Markets 20.00% Mid East
10.00% North America
9.00% Eastern Asia
9.00% Africa
8.00% Northern Europe
7.00% Domestic Market
7.00% Western Europe
6.00% South Asia
6.00% Eastern Europe
5.00% Southern Europe
5.00% Oceania
4.00% South America
3.00% Central America
1.00% Southeast Asia
Company Certifications ISO 9001:2000;CE;API;ENVIRONMENTAL MANAGEMENT SYSTEMS CERTIFICATION CERTIFICATE

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Tianjin,Shanghai
Export Percentage 71% - 80%
No.of Employees in Trade Department 11-20 People
Language Spoken: English, Chinese, Japanese
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range