FRP Chimney/Flue/Shower Pipe

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

FRP chimney, flue and shower pipe used in wet desulphurization system and the complete  equipment have obvious technical, economic and social benefits, along with long service  life, reliable operation, high corrosion resistance and energy conservation.

 FRP structural style:

1

FRP chimney nested inside Concrete. It is mainly applied to the height of 100m-240m concrete chimney inner tank used to flue gas.

2 FRP chimney coated with steel. Its usual design height is below 100m, with combining with desulfurization tower.

According to customer requiremnets to produce the different sizes.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the disadvantages of glass fiber reinforced sand pipe?
Not agree with the recommended answer, the same thickness of glass fiber reinforced plastic sand pipe and process tube, process tube stiffness is not low (can be calculated). The effect of sand inclusion is mainly to reduce the cost.
Q:Glass tube has different diameters with different prices. Who can elaborate?
According to the standard requirements, DN25-DN2500 pipes can be produced. The pressure levels are gravity flow, 0.6MPa, 1.0MPa, 1.6MPa
Q:Galvanized steel sheet and inorganic glass fibre reinforced plastic pipe are calculated according to this norm or norm
According to the project of quota valuation mode, input the actual quantity according to the quota item number, the following materials will automatically adjust the quota quota project, has been considering material wastage, when engineering calculation does not need additional.
Q:Winding method of glass fibre reinforced plastic pipeline anticorrosive glass fiber cloth
When the length and width of glass fiber mesh are not enough, the method of lap joint must be adopted to improve the tangential bearing capacity of the joint, so as to effectively overcome the radial tensile stress, bending force and bending shear stress. The lap length of the glass fiber cloth at the joint is generally 50 to 100mm, and the joint of each glass fiber cloth should be at a certain distance from the adjacent joint. The longitudinal and transverse joints between adjacent layers shall be greater than 300mm, and the distance from the same seam shall not be less than 500mm.5) paste made of circular duct, glass cloth along the radial 45 degree angle to the direction of cut cloth; conical paste products, according to the fan-shaped cloth.
Q:Glass fiber reinforced plastic GRE pipe broken hole how to repair and repair?
Resin selection of good points, the general also line, as well as accelerators, curing agents, high-quality glass fiber cloth.
Q:Raw material and mix ratio of inorganic glass fibre reinforced plastic wind pipe
Glass, reinforced with filler, the general ratio is 1 to 0.001
Q:What are the advantages of FRP pipes?
As a result, aviation, rockets, aerospace vehicles, high pressure vessels, and other applications that need to reduce weight have excellent results. The tensile, flexural and compressive strengths of some epoxy FRP can reach over 400Mpa.
Q:What is the stiffness of FRP pipe?
The ring stiffness is the comprehensive parameter of the tube's resistance to external pressure. Obviously, the choice of ring stiffness is one of the keys to ensure the safe operation of plastic underground drainage pipe under the external compressive load. If the ring stiffness of the tube is too small, the tube may undergo excessive deformation or buckling failure. On the other hand, if the ring stiffness is chosen too high, the excessive cross section moment of inertia must be used, which will result in too much material and too high cost.
Q:What kind of material is the pipe of the pipe that installs the pressure transmitter of GRP conduit? Is it fiberglass or carbon steel?
It is generally assumed that it is made of glass fiber reinforced plastic. The main pipe is made of glass fiber reinforced plastic. The medium is corrosive. Other materials must not be suitable
Q:How can I replace the valve on the water supply pipe?
The length of the steel flange three way pipe fittings can be determined according to the size of the expenditure caliber, and the specific processing can refer to the atlas of the water supply and drainage standards, and the steel pipe fittings processing standard drawing is made;

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range