Frequency Inverter Single-phase 200V class 0.75KW MINI Series

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Technical specifications

Table 2.3: Technical Parameters of QD200 Series Frequency Inverters

ITEM

SPECIFICATIONS

Main

Input

Rated voltage and frequency

Single-phase 200V class:  200V-240V,50Hz/60Hz

3-phase 400V class:  380V-480V , 50Hz/60Hz

Allowable value of change

Voltage: 380V-15% ~ 480V+10%;  Frequency: ±15%

Main output

Output voltage

Maximum output voltage equals to input voltage

Output frequency

0.5 Hz to 400 Hz

Overload capacity

150% of rated output current for 60s, 200% of rated output current for 2s

Control performance

Modulation mode

3-phase PWM, 2-phase PWM

Control mode

V/f control for constant torque, V/f control for quadratic load, vector control without PG (open loop control),Energy-saving

Setting method of run command

Outer terminal, keyboard panel or serial communication

Setting method of speed command

Analog setting, keyboard, serial communication, UP/DOWN speed setting from external terminal

Speed setting resolution

Keyboard: 0.1 Hz

Analog setting: 0.05/50Hz (10bit)

Speed control precision

V/f control:±2%

vector control without PG (open loop control): ±0.2%

Speed control range

V/f control 1:40

vector control without PG (open loop control)  1:200

Acceleration and Deceleration

Time

0-3200.0s

switching frequency

1.5 kHz ~ 12 kHz, according to junction temperature automatically reduce the switching frequency

Analog input

Number

2 ways: AI1、AI2

Type

DC voltage or DC current

Maximum input range

AI1: 0 to 5VDC, 0 to 10VDC, 0/4 to 20mA DC receivable

AI2: 0 to 10VDC or PTC probe input receivable

Analog output

Number

1 way: AO1

Type

DC voltage or DC current

Maximum input range

Voltage output: 0 to 10V, Current output: 0/4 to 20mA

logic input

Number

0.75kw-11kW:LI1,LI2,LI3,LI4,AI1,AI2

15kW-500kW:LI,LI2,LI3,LI4,LI5,LI6,LI7,LI8,AI1,AI2

note:2 virtual logic input, capable of configuring AI1 and AI2 into logic input port (positive logic or negative logic)

Type

Source or Sink

Maximum input range

0-24VDC

ITEM

SPECIFICATIONS

logic output

Number

0.75kW-11kW: pulse signal output (LO-CLO)、relay output 1(T1A、T1B、T1C

15kW-500kW:pulse signal output(LO-CLO)、relay output 1、2(T1A-T1B-T1C、T2A-T2B-T2C

pulse signal output

OC,output frequencycurrentoutput、ect other function

relay output

RA-RB-RC, including a NO contact and a NC contact

Maximum switch capacity:

T1A,T1B: 3A at 250VAC, or 4A at 30VDC

T2A,T2B: 2A at 250VAC or 30VDC

Serial communication interface

RS485 interface supports Modbus protocol.

Display

4-digit LED digital display

For display of frequency setting, output frequency, fault code and parameter setting etc.

Environment

Standard

Development of VSC200 series frequency inverters follows strict international standards and relevant recommended IEC and EN standards for control devices, especially IEC/EN61800-5-1 and IEC/EN61800-3.

Altitude

Derating unnecessary when altitude is 1000m or below (Derating necessary at altitude higher than 1000m)

Ambient environment

0.75kW-11kW: Reliable operation at -10 ~ 50°C without derating. When top protective cover is taken off, the environment temperature can be as high as +50 °C. Above +50 °C, the current drops by 2.2% for each rise of 1 °C in temperature. 15kW-500kW: Reliable operation at -10 ~ 40°C without derating.

Storage: -25 ~ 70°C

Humidity

No condensed water or drip at 5 ~ 95%, In accordance with IEC60068-2-3

Impact strength

15gn for continuous 11ms, In accordance with IEC/EN60068-2-27

Maximum antipollution capacity

Class 2, in accordance with IEC/EN61800-5-1

Structure

Protection level

Top: IP41 (without removing the protective top cover). Other parts: IP20

Cooling Method

Forced Air cooling

Installation method

Wall mounted

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The inverter is running independently
Principle of operation The main circuit is to provide asynchronous motor to the frequency conversion power supply part of the inverter, the main circuit of the inverter can be divided into two categories: voltage is the voltage source of the DC converter for the exchange of the inverter, DC circuit filter Is a capacitor. Current type is the current source of the DC into AC inverter, the DC loop filter is the inductance. It consists of three parts, the frequency power supply is converted to DC power "rectifier", absorbing in the converter and the inverter voltage ripple "smooth circuit." The basic composition of the rectifier unit: the fixed frequency of alternating current converted to direct current. High capacity capacitance: store converted energy. Inverter: high-power switching transistor array composed of electronic switches, the DC into different frequency, width, amplitude of the square wave. Controller: According to the set program work, control the amplitude of the output square wave and pulse width, so that superimposed as an approximate sine wave AC, drive AC motor.
Q:Notebook plug in the power adapter lights, but can not open the machine
1. Remove the power adapter and battery, the host does not power the case, hold down the boot button does not move, keep the notebook 30 seconds to release the residual static electricity; 2. Connect the power adapter separately to try to power on; 3. Connect the battery separately to try to boot; 4. If conditions permit, you can plug the memory test.
Q:Will the laptop's power adapter is not the original good?
See the adapter is suitable for notebook models to use, the following three conditions for reference: 1. The output voltage of the adapter is the same as that of the notebook. 2. Is the adapter's output current consistent with the notebook's requirements? (Or a little bit of the current is also not.) 3. The size of the joint is appropriate. (If the connector is too loose, will be bad, excessive fever.)
Q:Jd1a-40 motor speed controller and how to connect the motor
First, variable pole alignment speed method This method of speed control is to change the stator winding winding red method to change the cage motor stator pole pairs to reach the speed control target, the characteristics are as follows: This method is suitable for production machinery which does not need stepless speed regulation, such as metal cutting machine, lift, lifting equipment, fan, water pump and so on. Second, the frequency control method Frequency control is to change the frequency of the motor stator power supply, thus changing the speed of its synchronous speed control method. Frequency converter system can be divided into exchange - DC - exchange converter and exchange - exchange inverter two categories, most of the current domestic use of cross - straight - cross frequency converter. Its characteristics: This method is suitable for the requirements of high precision, better speed performance.
Q:In the official website to buy ThinkPad notebook, to the power adapter?
Hello, generally there will be a power adapter with Kazakhstan, unless there is a special note bare metal
Q:Inverter principle eff23
The basic principle of the inverter The inverter is a device that converts the power frequency (50Hz or 60Hz) into AC power of various frequencies to realize the variable speed operation of the motor. The control circuit completes the control of the main circuit, and the rectifier circuit converts the alternating current into direct current and DC Circuit rectifier circuit output smooth filter, the inverter circuit will reverse into the DC power.
Q:Can the four motors be tuned to 2900 rpm?
You have to look at what is the load, and look at the motor bearing can not bear 2900 turn, if the line, then under normal circumstances are possible. Only to the speed up to the motor rated speed above, the motor output torque is reduced.
Q:Will the asynchronous motor pole change the number of speed control can also be combined with the frequency converter
Of course, because the factors that determine the speed of asynchronous motor power supply voltage, frequency and motor pole pairs, so asynchronous motor speed can be achieved by changing the number of magnetic pole pairs, but this method needs to make a greater motor changes, Trouble, and change the number of poles can only achieve a single speed change;
Q:How to choose a power adapter
With the seller to an output 20V ,, 0.5A IBM single hole power adapter
Q:On the laptop power adapter problem
Can be simply calculated; 19 * 4.74 = 90.06 90W 19 * 3.42 = 64.98 65W Obviously, the second is a virtual standard, can not be used It is not enough power, ranging from the adapter burned, while the motherboard is like other notebook hardware damage, unpredictable. The adapter is likely to burn after the high and low voltage to the notebook board burned the situation more common. My notebook is dell original 4.62A, when playing the game are very hot.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range