Forklift with 4 supporting points

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Forklift with 4 supporting points


Rated loading:4-5T


Operation height:3000MM


Free lifting height:150MM


1.Specially common in warehouses and other large storage facilities;

2. forklifts serve the needs of various industries.

3.Some allow the operator to sit while driving and operating the machine; others require the operator to stand.

4.Some are powered by onboard batteries; others use different kinds of fuel.

5.Regardless of the type, however, all forklifts perform the same basic functions.

Forklifts are one of the smallest drivable pieces of machinery. They are compact enough to fit in relatively small areas and are easily maneuverable to turn in various directions. Depending on the forklift, many can handle carrying loads up to 35,000 pounds. Smaller forklifts may only have a 3,000 or 5,000 pound capacity, however.

There are three main types of forklifts, each used for different main purposes.

Internal combustion forklift are generally used outdoors because they are powered by gasoline, diesel, compressed natural gas or propane.

This type of forklift emits exhaust gases and therefore is generally not used indoors. Electric forklifts offer benefits for indoor uses.

They are powered by batteries, are less expensive to operate compared to gas-operated lifts and are much quieter.

Manual forklifts are non-motorized units and are not as versatile as the other two kinds. They can only lift goods off of the ground several inches and have a low load capacity.

The use of forklifts allows companies to easily move goods around. It eliminates the need for manpower and reduces the amount of time required to move goods. Forklifts also allow companies to move things up and down to higher locations than what could be reached by hand.




Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are some of the common failures of forklifts?
Forklifts cannot be started with the following conditions: 1, the battery without electricity Failure of starter The key switch is bad 4, the oil pump does not supply oil 5, there was no oil tank 6, no oil 7, the crankshaft lock The engine was completely scrapped
Q:Diesel forklifts generally take a long time to replace the oil
Run 150 ~ 200 hours for oil change..Normally, the oil and oil filter will be replaced in about 200 hours.
Q:What are the requirements for a forklift
Forklift workers have conditions for both employers and employers: Recruiter: Industrial units that are lawfully operated and operated by relevant regulations; The forklift truck needs to meet the ISO/TC110 industrial vehicle standard.
Q:Can a forklift drive into a container? Can the pallet be installed on the second floor?
As long as it's not big tonnage forklift, can be moved into the container, loading port container yard, warehouse, rarely used human handling large range, more is to use forklift to carry on the packing, only need some goods or to users of the tooling position very small place. There are many kinds of trays. It also depends on the strength of the tray and the weight of the goods on the tray. In general, light industrial products, such as a cubic metre (1 x1x1m) tray, column will be about 10 cm in diameter, weight about the above cargo pallets in 200 ~ 300 kilograms, can be packed to the second floor. All goods in the container need to be put on the second floor, otherwise they will be too bad. Ordinary pallet goods are likely to have a third layer of code. But it will need to rely on experience, warehouse workers and scheduling can help you to solve, such as packing is firm enough, packing, you can ask workers to help you to reinforce the packing fee.
Q:Whether there is a national standard or standard for the charging of forklift truck in the factory
The battery charging or storage site should be kept well ventilated, with ventilation and ventilation facilities to prevent the explosion of combustible gas. Smoking in the charging room of the forklift truck is prohibited from smoking. No phone calls in the rechargeroom, such as phone calls to the charging room. 3, as the electrolyte in the battery is a mixture of sulfuric acid and aqueous solution, toxic and corrosive, so when to battery charging and near its must wear overalls and protective glasses. If your skin or eyes are stained with electrolyte, rinse immediately with water and if you have an electrolyte in your eyes, turn to your doctor immediately
Q:How do you start a forklift without a key
Take the lid off the steering wheel. 2, find the junction box behind the key (ignition switch) and open it. 3, there are three wires in the box, connecting the red line and the black wire (ignition starter motor). Notice if there's a gap! Another way is to find a few people to push, get to a certain speed and hang fast and the ignition is successful!
Q:What is the engine displacement of 3T forklift?
Engine Displacement is the total volume of Engine Displacement, the product of Vh and number of cylinders. The cylinder work volume refers to the volume of gas that the piston has swept from the top to the bottom, which is also known as the single cylinder, which depends on the diameter of the cylinder and the stroke of the piston.
Q:Is a forklift and a hug a car
You said car is double forklifts, forklift truck can be modified, front is equipped with a quote, it is mainly used for paper pattern, such as cotton, no single evidence, a forklift truck operation certificate
Q:What happens when you do the force forklift
If it's a manual, it could be a disjoint. Or pressure plate.Your car (dangling from side to side of the wheel) is supposed to be the shaft of the door.
Q:About the safety of driving forklifts
Keep in mind that the goods are overloaded and don't try, or you will be fired by your boss. Insert the insertion of the teeth, the distance between the teeth, the higher the load, the lower center of the drive.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range