Forging Brass Ball Valve Reduce Port with Steel/L HandleXBV-05

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
100 pc
Supply Capability:
10000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

1. Manual Wafer Ball Valve Description

A ball valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a butterfly valve, which allows for quick shut off. Ball valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.

 

2.Main Features of the Manual Wafer Ball Valve 

a)Cast hole. Flange connection meet ANSI 125/150#   DIN PN10/16   BS4504 PN10/16 in the meanwhile.

 

b)Soft seat. Replaceable. Increase of service life.

 

c)Double half shaft without pin.

 

d) Square and short neck. Easy to stick scutcheon and cost saving.

 

3. Manual Wafer Ball Valve Images

 

Forging Brass Ball Valve Reduce Port with Steel/L HandleXBV-05

Forging Brass Ball Valve Reduce Port with Steel/L HandleXBV-05

4.Manual Wafer Ball Valve  Specification

 

Forging Brass Ball Valve Reduce Port with Steel/L HandleXBV-05

Forging Brass Ball Valve Reduce Port with Steel/L HandleXBV-05

 

5.FAQ

 

1. What is manual wafer ball valve?

A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style ball valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a ball valve. It is taken for granted that if a ball valve is ordered, a wafer style will be received.

 

2. How about the Installation of the Wafer Style Ball Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.

 

3. What is the working principle of manual wafer ball valve?

 A: A ball valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "ball" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What does valve DN50/80 mean?
DN refers to the nominal diameter unit mm, that is, the diameter of the pipe. DN 5080 is the diameter of 50mm 80mm
Q:What are the valve types H, F, and Y? What are the meanings of these 3 letters?
Please refer to "JB/T308-2004 valve model preparation method"Sealing surface material codeH Cr13 stainless steelF fluoroplasticY cemented carbide
Q:I want to act as a proxy valve
As the saying goes, the valve does not break up. The type of valve is too much, I do not know what you want to proxy valveIf you want to take advantage of the price, please go to Tianjin, or go to the township of Henan valve to see the followingIf you want to take advantage of quality, please go to Henan's Gaoshan Valve Co., Ltd., Yu Ming Valve Co., Ltd., Zhengzhou high and low pressure valve Co., Ltd... I am the valve distributor in Shenyang
Q:How big valves are used in a DN159 pipe?
DN159 is the valve with the DN150 in the outer diameter of the pipe.The valve size of the pipeline is classified by nominal diameter:1, the small diameter valve: nominal diameter DN = 40mm valve.2, medium diameter valve: nominal diameter DN from 50 to 300mm valve.3, chase diameter valve: nominal valve DN for 350 ~ 1200mm valve.4, large diameter valve: nominal diameter DN = 1400mm valve.The components of the valve must be handled following process before they are assembled:1, according to processing requirements, some parts need polishing, surface processing burr can not be;2. All parts are degreased;3, after degreasing, pickling and passivation, the cleaning agent does not contain phosphorus;4. After pickling, rinse with pure water, no residue of medicament, and carbon steel parts shall be omitted;5, one by one parts with non-woven fabrics dry, not cable, hair and other retained parts of the surface, or with clean nitrogen drying;6, with non-woven fabrics or precision filter paper, stained with pure alcohol, wipe parts by one, until there is no dirty color.
Q:What does the "PN" mark on the valve mean?
The valve will usually be marked with "DN.PN." these two signs,DN refers to the valve path, and PN refers to the pressure levelFor example: DN25, PN16Refers to the valve diameter of 25mm valve, the pressure is 16 kg (1.6Mpa)
Q:How can the material be checked by valve approach? What experiments do you need?
May refer to the valve pressure test principle and the pressure test matters needing attention.(1) in general, the valve shall not be subject to strength test, but the body and bonnet shall be subjected to strength tests after the repair of the valve body and bonnet or corrosion damage. For the relief valve, the constant pressure and seat return pressure and other tests shall be in accordance with the specifications and the relevant regulations.(2) the installation of the valve should be done for strength and tightness test. Low pressure valve sampling 20%, if not qualified should be 100% of the inspection; medium and high pressure valve should be 100% of the inspection.(3) the installation position of the valve shall be in the direction of easy inspection during the test.(4) welding connection valve, not with blind plate pressure test can be used when the cone seal or O ring seal pressure test.(5) when hydraulic test, the valve air will be excluded as much as possible.(6) the pressure should be increased gradually during the test, and the pressure will not be sudden and sudden.(7) strength test and sealed test duration is generally 2~3min, important and special valves should last 5min. Small caliber valve test time can be a little shorter, large caliber valve test time can be longer. During the test, the test time can be extended if in doubt. Strength test, does not allow the body and bonnet sweating or leakage. Sealing test, the general rotor valve only once, the safety valve, high pressure valve and other raw valve to be carried out two times. When testing for the low pressure, large diameter valve is not important and there are provisions to allow leakage of the valve, allowing a small amount of leakage; the common valve, power station valve, marine valves and other valve requirements vary on leakage requirements according to relevant regulations.
Q:So how does the valve turn on?
The handle of the valve is opened along the pipe and perpendicular to the pipe
Q:What's the name of the valve?
Specific models only go to the original manufacturers to find, and want to use other valve replacement is not impossible, want to provide detailed parameters. Let's go to the valve manufacturer!
Q:Is there any difference between the valve and the water valve?
There is no difference between the low pressure lubricating oil pump, as long as the excuse right on the line, not to pressure, design pressure ball valve common does not exceed 3MP, the maximum pressure of only small gear pump vane pump is 2.5MP, the other piston pump, gear pump, the pressure is above 6.3MP. Certainly not. Unless using high pressure water pipe valve.
Q:In the fire drawing, what valve does the following valve represent?
Are you in the sprinkler system? Signal valve and alarm valve

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range