Forged Steel Pipe Fittings Half Threaded Short Pipe

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
10 Pieces pc
Supply Capability:
10000 Tons per Year pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Detailed Product Description

Forged Carbon Steel/Forged Stainless Steel Pipe Fittings

Half Threaded Short Pipe

Design and Manufacture: ASTM/ANSI B16.11, B1.20.1, MSS SP-79, 83, JIS B2316

Ends: Socket Welding/Threaded NPT

Nominal Diameter: NPS 1/8"-4"(DN6-DN100)

Threaded: 2000LB-3000LB-6000LB

Socket Welding: 3000LB-6000LB-9000LB

Material: ASTM A105, ASTM A182 F304,F304L, F316, F316L

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Very confused about the pipe fittings and the fittings, and can not distinguish them
The task is accomplished by the joint body, one end of which is connected to the pipe joint and the other end connected to the device
Q:Joint type of pipe joint
NPT is the abbreviation of National (American) Pipe Thread, an American Standard 60 degree taper pipe thread, used in North America. National standards refer to GB/T12716-1991PT is the abbreviation of Thread Pipe, is a 55 degree taper pipe thread sealing, belonging to the Whitworth family, for the European and Commonwealth countries. Commonly used in water and gas pipe industry, taper regulations of 1:16. national standard is available on the GB/T7306-2000G is a 55 degree non thread sealing pipe thread, belonging to the family of Wyeth thread, marked G for cylinder threads. National standards refer to GB/T7307-2001In addition, the 1/4, 1/2 and 1/8 marks in the thread refer to the diameter of the thread size, in inchesYes, my wife usually refers to the size of the thread by one point, one inch equals 8, and 1/4 inches is 2, so by analogy
Q:Does the American and English fittings how to recognize it?
What's the amount of taper thread you want? This is really a bad amount. Taper pipe threads are specified: within the range of the effective thread length, there is any place that meets the requirements (as you say, NPT1/2), because the pipe threads are sealed with little depth. Only a few teeth used for sealing, but the thread specification according to the requirements, for example, you say NPT1/2-14, then the pitch is 1/14 inches, in addition, the effective thread in a certain position must be the nominal diameter of 1/2 inch. I don't know, I said so, you know, no, no, I don't have a good idea for you, but I'm sure I didn't cheat you. I'm doing this, not an expert, but it's my business, huh?.
Q:Quick plug and card sleeve joint sealing which good?
Quick plugPlug connection is the most convenient plug and play connection mode, especially in some of the trachea connection is very inconvenient, difficult space occasions, can better reflect the advantages of fast plug.
Q:PT1/4 large diameter pipe joint? No figure urgently
Taper Pipe Thread is an inch taper pipe thread standard with a thread shape of 55 degrees
Q:Hydraulic pipe quick coupling principle of hydraulic pipe joint
Quick change joint, one is with one-way valve, and the other is without one-way valve. The application with a one-way valve, a one-way valve end is connected with the gas source, when the check valve closes automatically when connected to a one-way valve open end of the thimble. Self locking is the use of steel balls embedded in the groove, while the "cone - cylinder" sleeve to lock the ball.Type, type, structure diagram, characteristic table and standard number of pipe joint, welded pipe joint is welded by pipe and pipe. The sealing surface of the O sealing ring is sealed between the joint body and the pipe. The utility model has the advantages of simple structure, easy fabrication, good tightness and low requirement for the dimension precision of the pipe. High welding quality, inconvenient assembly and disassembly. The working pressure can reach 31.5MPa and the working temperature is -25 to 80 degrees. It is suitable for the piping system with oil as the medium. Table 6~14The JB966 ~ 1003-1977 card sleeve pipe joint is jammed and clamped by the deformation of the clamping sleeve. The utility model has the advantages of advanced structure, good performance, light weight, small size and convenient operation, and is widely used in the hydraulic system. Working pressure up to 31.5MPa, requiring high dimensional accuracy of the pipe, cold drawn steel pipe is required. The card sleeve is also of high accuracy. Piping systems for oil, gas and general corrosive media 15~26
Q:New standard, how can the pipe joint be labeled, such as "3/4" taper pipe thread?
Pipe fittings 3/4 refers to the pipe fittings of six points (6 British points), DN (diameter) of 20mm, the outer diameter of 26.8mm.Supplement:1 inches =25.4 mm, =8 British points, 1/2 is four points (4 British points), DN diameter 15mm, 3/4 is six points (6 points), DN20mm.
Q:Why is the water purifier on the quick connector and contact Water Leakage PE
If the connection is fast, it's only possible to change the connector, change the connector and plug it into the bottom, then put the cards on it. After changing the line when the first card, then hold the joint to joint in force according to the pipe out, gently, not pull, pull the useless.
Q:Connect with stainless steel tube with 304 stainless steel clip type pipe joint,
I personally think that the installation problem, that is, the card sleeve and steel pipe only after installation to reach the sealing effect, the installation quality can not meet the design pressure requirements.To avoid this situation, it is recommended that after installation 1.25 times higher than the design pressure test, test pressure can be put into use
Q:PT3/4 what is the diameter of the pipe joint?
Diameter: Phi 23.6 mm.Taper Pipe Thread is an inch taper pipe thread standard. Threaded pipe threads (GB 7306 and ISO7/1).
Our products can be found in more than 100 countries and regions all over the world. We have registered 31 trademarks in China and abroad, also we become OEM of many famous International companies.We also have big investment in many factories, through this, we have build up a very strong throughput, so whether the price is going down or up, we are always the one who can offer you lowest price and best quality together.

1. Manufacturer Overview

Location Hebei,China (Mainland)
Year Established 2004
Annual Output Value
Main Markets North America
South America
Eastern Europe
Southeast Asia
Africa
Oceania
Mid East
Eastern Asia
Western Europe
Company Certifications IMPORT AND EXPORT REGISTER;CE;QUALITY MANAGEMENT SYSTEM CERTIFICATE

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range