Forged steel fitting SW TEE ASME B16.11 3000LB DN15 A105

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Tee
1/8" to 4" class 2000 threaded
1/8" to 4" class 3000 threaded & socket weld
1/8" to 4" class 6000 threaded
1/8" to 4" class 6000 socket weld
1/2" to 2" class 9000 socket weld

Material:

CS: A105  

AS: F5 F9 F11 F22 F91

SS: F304/304L F316/316L F51 F60 F53

Standard:ASME/ANSI B16.11 BS 3799 GB/T14383

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Hydraulic pipe fittings, DIN, GB, American Standard how to distinguish?
ZG is a commonly known as cone, cone thread processing, pipe joint is generally the old GB marked Rc for metric threads to represent the thread pitch, with every inch of the thread number, this is the biggest difference between them, metric thread is 60 degrees equilateral tooth type. 55 inch thread is isosceles tooth type of thread, 60 degrees. Metric units for metric threads; British and American systems. Pipe thread is mainly used for pipe connection, the internal and external threads are closely matched with straight pipe and cone pipe two kinds. Nominal diameter refers to the diameter of the pipe to be connected. Obviously, the diameter of the thread is larger than the nominal diameter. 1/4, 1/2, 1/8 is the nominal diameter of inch inch, inch in inches.
Q:May I ask what material EN39 is? Used to make a threaded pipe joint
EN39 is a European standard, the standard number is EN39:2001. The standard formal name is: carbon steel pipe for scaffolding.
Q:Stainless steel pipe, wire joint leakage how to make up?
1) want to save trouble, buy special glue to block, general hardware store can buy;2) the silk joint opens, the more winding some raw rubber tape, then turns tight to see whether can solve the problem;3) if it is a silk joint, replace the wire joint;4) the pipe is re tapped or replaced with a new pipe;
Q:What are the standards for the pipe connections at both ends of the cone pipe?
Because of this transition joints, because of doing too much, but do not know what the standard, and many times is an industry or business standards it? Normally, this is called a pair of silk. Relatively simple production, large dosage.
Q:What are the installation requirements of the card sleeve joint?
The ends of the pipe shall be flush. The pipe should be flush in sawing grinding wheel and other tools, and burr cleaning and high pressure air blowing after use.When installing, the coaxiality of pipe and joint body should be kept as far as possible. If the pipe deflection is too large, it will cause sealing failure.The pre assembly force should not be too large. The inner blade of the clamping sleeve is just inserted into the outer wall of the pipe, and the clamping sleeve should not be deformed obviously. When the pipeline connection, and then according to the specified tightening force assembly. The tightening force of the phi 6-10mm card sleeve is 64-115N, Phi 16mmr 259N, Phi 18mm is 450N. If the sleeve is badly deformed at pre assembly, it will lose its sealing effect.(2) prohibit adding sealant and other fillers. In order to obtain better sealing effect, the sealant is coated with sealant, and the sealant is poured into the hydraulic system, causing the hydraulic components, such as damping holes, blocked and so on.(3) when connecting the pipe, the pipe should have enough deformation allowance to avoid the tensile stress of the pipe.(4) when connecting the pipeline, it should be avoided to be subjected to lateral force; the lateral force will cause the seal to be too lax.
Q:Standard for fabrication of jacket type pipe couplings for card sleeve couplings
6 flared flared joint (GB/T 5630-2008)7 、 flared type adjustable end bend pipe joint (GB/T 5631-2008)8 、 flared type combined bend pipe joint (GB/T 5632-2008)9 、 flaring type adjustable end to end three way pipe joint (GB/T 5633-2008)10 、 flared type combined bend three way pipe joint (GB/T 5634-2008)
Q:What are the names of all types of hydraulic pipe couplings?
Welding type, sleeve type and flared type, according to the function of many kinds of joints, such as: the end of the straight joint and straight joints, three joints, elbow, with movable nut joint, hinge joint, plug, adapter etc..
Q:What is the function of the pipe joint?
This is a general term for connections that can be disassembled in a fluid path. It mainly includes welding type, clamping sleeve type and flaring type
Q:The pipe connections have different diameters. Reducing the diameter, what else?,
According to the form of joints: pipe plug, two - way connector, three - way connector, four - way connector,
Q:PVC how to deal with leaking water in the upper opening of three pipe joint of launching pipe?
To buy a bottle of UPVC dedicated glue, and then go to the production of PVC pipe manufacturers, where they want a little PVC resin powder

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range