Folding Square Table

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
30 Pieces pc
Supply Capability:
3000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Detailed Product Description

1.modern design,green environmental recycled material

2.lightweight,easy to move and store

3.long service life

 

this square table is constructed of high density polyethylene and are stronger , lighter and more durable than wood . 

Plastic tables will not crack , chip or peel , and are built for indoor and outdoor use .

The patented steel frame provides a sturdy foundtion and is protected with a  powder-coated finish .

It excellent for dining , restaurant  . 

 

Details

 

Item No.BXF88
MaterialHDPE & Steel
ColourGrianite
Table top thickness4.5cm
Open size89*89*74cm
Carton size89.5*89.5*6cm
N.W/G.W9.3/10.5kgs

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the advantage of hydraulic automatic transmission of grinding machine table?
You should consider this horizontal hydraulic transmission and power transmission, vertical movement speed is adjustable, this premise is that you must use stepper or servo motor or pneumatic drive mode, compared with the hydraulic transmission, pneumatic transmission stability is relatively poor, and the motor drive mode and the maintenance cost the mechanical structure of production costs are relatively much higher, so the workbench of the grinding machine using hydraulic drive is the best choice in the economy and the mechanical design.
Q:I want to install the cylinder on the rotary table. I want to use pneumatic rotary joint to solve the problem of trachea winding. Can you tell me if the rotary joint is connected to the cylinder or what?
Not connected to the cylinder. It is attached to the rotating part
Q:How to connect NC rotary table with control system?
Don't you have an electrical wiring diagram? No machine is different
Q:Is the indexing head the same as the rotary table?
No, the indexing head is a rotating shaft parallel to the horizontal plane of the work tableThe rotary table is usually vertical to the horizontal surface, and it does not necessarily have an indexing device
Q:CNC machine tools work surface milling a hole, do you know what method to repair it?
Upstairs, the method is 100 percent feasible ah.1. change the workbench2. milling the entire table may require technical guidance from the manufacturer
Q:What is the workbench?
Kam Tian kitchen utensils for you to answer: double deck table series products, are made of high-quality stainless steel, can also be customized according to user requirements. The panel is made of mould and formed by bending at once. It is smooth and natural without solder joints. It is easier to clean and durable, and never loosen.
Q:Why should the machining center be applied to the worktable?
When programming, the base plane is the workbenchThe aim of the tool setting is to determine the position of the origin of the program in the coordinate system of the machine tool. The tool point can be located on the part, on the jig or on the machine tool. When the tool is set, the tool point should be coincident with the cutter location. The trial cutting method is the most widely used tool setting method in practice.
Q:Bed electrical control technology, as shown in the diagram, ask: if the work station to run at both ends, want to stay for 10 seconds, how to control the design of the circuit?
A time relay in his one normally open contact to coil KM1, KM2 series electric locking loop, that is to say the motion of the platform to end, after the pressure switch, give him a ten seconds delay to contactor inversion of control power, so that we can realize that work Taiwan stop 10 seconds, ten seconds to remember to pay attention to the time relay is reset, the coil circuit loss of electricity, or directly to the other end of the reverse.
Q:Working principle of machine tool table
It is mainly used in the plane of machine tool processing. There are holes and T grooves, which are used to fix the workpiece and to clean the iron filings produced during the process. Manufactured according to JB/T7974-99 standard, the products are made of ribs, plates and boxes. The working face is scraped and scraped, and V, T, U and round holes and long holes can be machined on the working face.
Q:To answer why the Excelle table is split into it nabuxialai
I can move, and I can't take it off. It seems to have been blocked by the front block.
Our products are exported to more than 10 countries and areas at present, such as the United Stated, Europe and South America, having received great favors from all customers. We sincerely welcome customers from all over the world to offer drawings or samples to co-develop products with us. Let's create a bright future together.

1. Manufacturer Overview

Location Zhejiang,China
Year Established 2008
Annual Output Value
Main Markets North America
South America
Southeast Asia
Oceania
Eastern Asia
Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range