Flange end double orifice/ball/hole standard ductile iron air valve

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
111 PCS
Supply Capability:
1000 PCS/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Quick Details

Standard or Nonstandard:

Standard

Structure:

Control

Pressure:

High Pressure

Material:

Casting

Place of Origin:

 

China (Mainland)

Packaging & Delivery

Packaging Detail:plywood case
Delivery Detail:60days after recieve your deposit

 

Specifications

Flange end and screw end ductile iron air bleed valve is used for water pipe in medium to protect the pipeline from deformation.

We are professional leading valves manufacturer, specification Variety&resonable price.welcome your inquiry!

 

 

Flange end double orifice standard air valve

conforms to JKR20200-0043-99

Flange drilled conforms to BS EN1092-2

Features:

1. Able to eliminate the gas pipeline, reduce resistance, saving energy.

 2. When this product pipeline negative pressure can automatically inhaled air prevent pipes burst.

 3. Float for stainless steel, service life factory, safe and reliable.

 

Material:

 Flange end double orifice/ball/hole standard ductile iron air valve

 

 

Dimensions

 Flange end double orifice/ball/hole standard ductile iron air valve

 

 scope of application

 

 Flange end double orifice/ball/hole standard ductile iron air valve

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Which direction is the valve? Which direction is it?
Ball valve: handle and Guan Daocheng 90 degrees for the pass, 180 degrees to open (ie in line with the direction of the pipe open)The gate: clockwise, counterclockwise.
Q:What does the PN on the valve mean?
1, mark "ON25" and "PN16" respectively what does that mean? 2, the valve above has an outer six corners, so PN16 refers to the nominal pressure of 16 kg valve. Valves on the fittings are standard parts, special
Q:How to check the quality of the valve?
First of all, to check the appearance of the valve is smooth and smooth. Cast valves without sand holes and obvious flaws. Forged valves check nominal pressure or pound level.Second, check the material of the valve, that is, the material composition, this is very important, the material does not meet the standard on the device will be a big problem.Finally, check that the switch is sensitive and the signs are clear. Test pressure is the last step.Valve (Famen) is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves (201, 304, 316), chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..
Q:What valve does the high pressure by-pass valve DN254 * 800 belong to?
This is because the bypass valve is a special valve and other valve type theory.This is custom-made valves, generally no inventory, and may not have the material you need. So it needs to be customized.I remember the German HORA had the valve, but the price was sky high.
Q:Standard and specification for pressure test of valves
(11) when the valve with drive device is tested and its tightness is tested, the sealing test shall be carried out by using the driving device to close the valve. For manual drive units, seal test shall also be done with the actuating closing valve.(12) the by-pass valve installed on the main valve after the strength test and the sealing test. The strength and tightness test of the main valve is carried out. The main valve should be opened when the closing member is opened.(13) iron valve strength test, the application of Pratia tapping valve and valve cover, check whether there is any leakage.(14) the valve test, in addition to the provisions of the plug valve to allow sealing surface oiling, other valves are not allowed in the sealing surface of the oil test.(15) when the valve pressure test, the blind plate on the valve pressure should not be too large, so as to avoid deformation of the valve, affecting the test results (cast iron valve if pressed too tight, will be damaged).(16) after the valve test pressure, should promptly remove the water and clean the valve, should also be prepared for the test record.
Q:What does "DN15" mean? What does "PN 16" mean?
Valve DN15 refers to the nominal diameter of the valve 15mm, PN, 16 refers to the pressure of the valve is 1.6MPa.Nominal diameter (nominal, diameter), also known as the average diameter (mean, outside, diameter). DN is the nominal diameter (or nominal diameter), that is, all kinds of pipe and pipe accessories of the general caliber. The pipes with the same nominal diameter can be connected with each other, so they are interchangeable. It is not the actual diameter or diameter of the pipe, although its value is close to or equal to the diameter of the pipe.
Q:What are the major brands of valves abroad?
The best form is used to provide the valve and valve operating conditions, each brand has its own advantage.
Q:What does the "XV" valve mean?
XV:X said V is plug valve, said valve body material is chrome molybdenum vanadium steel.
Q:Valve difference
Valve difference, or you should ask the classification of valves, valve classification, there are several sub methods, some according to the model, and some are by use, then each kind of valve is divided into several categories and models. Take the trap for example, it is a kind of valve, and then it is divided into steam traps, air traps, float traps, and so on. If you really want to know the difference between the valve you search the Internet under the classification of the valve, there are a lot of articles, or you directly to the trap inside www.ssfmsh.com find an article on the valve type article, can not give you a specific address, is not allowed here. You work hard, go find kazakhstan. I hope my answer will be helpful to you.
Q:Our company is doing valve exports,
If the customs clearance order is required, the boxes, invoices, and contracts will not be needed. If the customs clearance is made, which port should be provided, the value of the goods, the weight, and the HS code for those

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range