F-KB086 Carbonized bamboo knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:rubber wood knife seat

material:Carbonized bamboo

N.W.:1.218kg

MEAS:23*20*10cm


Product advantage:

How does the bamboo product carbonize?Firstly,put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization.

And after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.


The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles  will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.

At the same time, because after carbonization the bamboo will be more hard than ordinary paper products,  preventing wearing and bamboo thorn problem.


Carbonized bamboo knife seat quantity:

Safety, health, bright color,durable,the everyday necessary good products

Anti-mildew change,anti moth

Environmental protection,no crack,no decay


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Why use the center and the rest?
In order to prevent the workpiece from bending deformation due to the radial cutting force, the central frame or the tool holder is used as the auxiliary support to increase the rigidity of the workpiece.
Q:Advantages and disadvantages of drift plate holder and S frame
Modified DIY it certainly is h good, can change the surface of bamboo wood aluminum can, spray painting stickers can... The support of the s arm than the low end of the non uniform force... The actual s arm didn't what reinforced technology, the most vulnerable to bad is that even if you part of aluminum, steel shaft intact, aluminum bent??? From the point of view of the wheel easy disassembly, s frame is much better, less two outer shaft on the convenience. As for the slide is more dependent on the wheels and bearings, s frame is close to the center of gravity of the Double Tour dragon board, h's center of gravity close to the long plate in the skateboard, of course, the difference is not so big, more difficult than the long board.
Q:What is a tray roll bag
Super large PE bag (tray bag, tray roll bag, super PE even roll bag): for the industrial production of super large PE bag, super PE roll bag.The utility model is mainly used for the packing of the pallet goods, various Super machinery, the packing of the goods, and the waterproof leakage proof of the swimming pool and the related buildings. Available for various specifications, various forms of super Dalian roll bag. The work efficiency is effectively improved, and the labor intensity is lightened.Material; PE, aluminized film, shrink film, etc. can be produced according to customer requirements. Maximum size; 8m/36m bag shape; top opening, side opening, m side, etc..
Q:CNC lathe tool holder with the right side of the knife how the thread?
Right hand can be turned back to the processing of G92 is also G92, hope to adopt
Q:The difference between the tool holder and the electric tool holder
Methods with 980 for example: the first knife in the knife up one page T0010 for the input of X0Z0 cutter compensation in T0020 dabbler cutter compensation second page cutter compensation input X0Z0, the rest of the line.
Q:What are the reasons for the deviation of the CNC lathe tool holder after each turn
The mechanical structure of the cutter head is damaged, the parts can be replaced, but the new tool holder is recommended. Because the replacement of mechanical parts is also difficult to ensure accuracy, it is best to change the tool holder.
Q:There is no difference between the tool holder and the tool holder
The operator is standing in front of the numerical control lathe, the cutter head is located between the main shaft and the operator. When the tool spindle is rotating, the tool head is turned upward, and the cutter head is rotating. The front and rear turret turret programming is the same, clockwise and counterclockwise circular interpolation G02 interpolation G03 direction is right according to the Descartes coordinate system, first determine the positive direction of the Y axis, and then from the positive direction of Y in the negative direction seems to determine the positive direction of the X axis, and then determine the G02 and G03 in the direction of the XZ plane can be, in front of the turret Y positive axis down, rear turret Y positive axis upward. No matter what the system is the same, if you in the right direction according to the right to see Descartes coordinate system can determine G02 and G03 in the front and rear turret style the same, the Y axis is a virtual axis lathe, there is practically no Y axis.
Q:What is the material of the cutting tool
Common materials:High speed steel (also known as Feng Steel, Bai Gang): is a kind of tungsten, chromium, vanadium, molybdenum and other high alloy tool steel more elements.Tungsten carbide hard alloy by high hardness and melting point, titanium carbide and cobalt cemented metal made by powder metallurgy method, the hardness and wear resistance are good, hot hardness is very high, so the cutting speed is higher than high speed steel several times or even several times, can not add high-speed steel cutting materials processing the work, but the bending strength and impact toughness of high speed steel much worse than.Ceramic: ceramic powder sintered at high temperature with alumina powder, the hardness, wear resistance and heat resistance are higher than those of cemented carbide.
Q:How to save the supermarket roll bag?
Free plastic bags can only do this! You can collect money to help him sort out the unnecessary waste of pocket, there is no loss can not do.
Q:The electric turret is installed on the tool rest in the lathe bed
If it is a CNC lathe that can install electric turret and four power head, but before installing X to find out the shaft of the motor power and torque (because you are inclined bed, before installation will calculate), and your head is driven by motor or pneumatic, according to the modified circuit and PLC the ladder diagram (if the pneumatic power head, aerodynamic outfit). Install the tailstock it depends on your machine is installed the tailstock, general CNC lathe should have the appropriate location to install the tailstock, you look to see if there is any guide, the tailstock in your machine is generally a mountain, or two. As for the price that depends on your choice of the tower and power head specifications, the brand to be there is the cost of renovation. It depends on the specific situation. You say these three kinds of knife tower and power head, good change is not very expensive, but artificial expensive

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range