Q:Thread style, whether it is the need for screws or something!What do I need to connect the two pipes to the groove joint?!Because I don't have much points, I hope you have some knowledgeable people to help me. Thank you very much!

Groove connection: This is the most advanced connection mode at present. There are two two connecting pipes, valves, or pipes and valves that are connected by clamps. In the outer pipe or valve connecting end have an annular groove manufactured according to the standard, when connected with a supporting clamp. Site construction, installation and disassembly are very convenient and quick. Not only the seal is reliable, but also saves time and material. It has incomparable advantages in large caliber connection.

Q:What are the specifications and models of hydraulic pipe fittings?

Three way, variable diameter, etc.. Specifications, models, tens of thousands. You want someone to make it clear to you that the joke isn't fun.

Q:This only happens at night, if we have the air conditoner on, after a few hours, our smoke alarm will start beeping in five minute intervals. We have four of them in the apartment and only one of them beeps. What could be causing this?

my parents had the same thing in thier old house water pipe coming from thier WELL. It didn't affect the water taste and no one got sick, but if you have concerns,send a sample to your state water testing facility

Q:I have an adorable track suit that I purchased from Victoria's Secret ages ago (the kind that nobody ever actually wears for track.. ^_~), and it's made from deep wine-red velour. I went to put it on earlier, and realized that while the *outside* was soft, sensual velour, the *inside* was scratchy and not all that soft.It's the same way with clothing that's satin, or silk, or velvet, or that smooth satin-like fabric that I don't know the name of it always feels wonderful on the *outside*, but *not* on the part that's against my skin.Why is this??

Use a magnet and lift it back out. If you leave it there it will over time collect hair and stuff and at least partially clog the drain.

Q:i have the axles of butt dont wont to break eneything

C cupped end - the type you would slide over another pipe to make a sweat connection FTG fitting end - the type that slides inside a cupped end, also called a street fitting M male pipe threads FE (sometimes listed as just F, not correct) female pipe threads There are several others, those are just the ones I can think of. The X is by, so C X C is cupped by cupped, a fitting with two ends such as a coupling or elbow, both cupped for sweating onto a pipe or fitting end. C X C X C would be a fitting with three ends such as a tee, all cupped. C X FTG could be a street elbow or a reducing bushing, one part slides over a pipe, the other inside another cupped fitting. C is indeed a cupped fitting. CMP is compression, but there is no such thing as a copper fitting with a compression connection. There are brass and plastic compression fittings that will fit copper pipe, but not copper compression fittings.

Q:So, sometimes when i cook it goes off and he freaks out. He runs and hides and he starts shaking like crazy. I try to pet him and calm him down but he just hides between my legs and shakes. if it does happen i try to fan the smoke out or before i start cooking i open the windows to let a breeze in. The noise is really loud though so i don't blame him. What are some ways to not get him scared and shaken-up and some ways to calm him down.

knight1192a has given you some excellent proof that the landings (all six of them) really did happen. For you to believe that the landings didn't happen, you have to accept the premise that the Federal government has managed to keep an airtight lid on things for over 40 years so that none of the 400,000 people who worked on the project, or several foreign governments (including the Soviets, who hated us) have ever said a word. You're asking this of the same Federal Government that couldn't keep the Watergate break-in quiet for 30 days, when there were fewer than a dozen people who knew. But here's another piece of evidence I've never seen the hoaxers be able to successfully explain. In the mid 1990's, the Japanese put the SELENE spacecraft in orbit around the moon. One of it's instruments was a device for measuring the height of the lunar terrain. This data could be reconstructed to give an extremely accurate ground level view of the surface (literally orders of magnitude more accurate than what was available before). When this was done with the Apollo landing sites, the reconstructed terrain matched the photos taken by the astronauts exactlyevery single time it's been tried. Since that data wasn't available until the 1990's, and the photos have been around since at least 1972, explain how those photos could have been taken any place other than the moon (keeping in mind that plenty of the pictures include astronauts, so they were taken by robots won't work as an explanation). You say that evidence supports we didn't. Given that every single piece of hoaxer evidence from the last 35 years has been refuted, I'm anxious to hear what new evidence you have.

Q:I'm not planning on making one, but I was curious how one would go about making a speed bump (say for a private company parking lot.) Is this a project that is best left to the professionals or a quick weekend project some good friends could help with?

Yes, I believe they are still here with us too. I've only had personal experience with Artemis, but I believe the others more than likely are around too.

Q:PPR pipe joints did not plug in the melt, in the end will leak?

6, the pipe and fittings into the fuse, heating according to the designated time;7, after heating, remove the pipe and pipe fittings, immediately connected in the pipe and pipe fittings connected with timely, if the position is wrong, can do a certain period of time in the mediation, but shall not exceed 5 degrees across the rotation angle;8, the connection is completed, both hands must grip the pipe and pipe fittings, to connect the rich cooling time, cooling to a certain extent, you can let go, continuous arrangement of the next section of the pipe.Three, after the completion of the pipe connection, should be on the wall or ground with colored paint to show the pipe position, to prevent the two decoration damage to the pipeline. If the water supply pipe is concealed, a strong supporting point shall be made to go through the floor so as to prevent the standpipe from accumulating and flexing, and to produce displacement stress at the uppermost branch pipe and cause damage to the branch pipe.

Q:Why is the water purifier of the PE pipe and quick connector contact after the start of Water Leakage, can be pulled out after turning and then inserted into the PE pipe does not leak, what is the reason ah, who knows?

Because there is no plug, the fast joint must be inserted in the end, through the internal sealing ring to play a role.

Q:PT1/4 large diameter pipe joint? No figure urgently

The basic size of large diameter pitch thread code P per inch TPI in diameter of external thread tooth type D3 path height H1 bottom hole sizeG, 1/4, 1/4, 13.157, 1.33719, 12.301, 11.445, 0.856, 11.6