EMC XLPE Wind Energy Shielded Control Cables

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
100 m
Supply Capability:
30000 m/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 Product Introduction:
The surface of conductor should be bright and clean no grease, no burr or bulge or faulted wire to  damage the insulation.Every conductor coat with an isolated layer made from appropriated material.
The nominal value of the insulation thickness shall comply with IEC60227-7. The average value of insulation thickness should be no less than nominal value, and the thinnest part should be no less than 90% -1mm of nominal value.
Insulation adopts XLPE, whose property should comply with provisions in IEC60502-1. The insulation should be rapped on conductor tightly and easy to peel without damaging the insulation, conductor and coating. The surface of the insulation should be flat and color evenly

 

Operating Characteristics:
• The lowest temperature that cable could work should not lower than-300C.
• Max temperature is 150 0C for short period ( 2h maximum duration each time).
 

Specification:

 Altitude: 1000m
Ambient air temperature: Perennial mean temperature: 10℃
Extreme high temperature:  50℃
Extreme low temperature:  -42℃
Average relative humidity: normal value for accumulated year: 80%
Earthquake Proof: Horizontal acceleration: 0.2g
Normal acceleration:   0.1g
Range of Laying:
Cables mainly lay in the cabin of fan, where machinery oil may leak or overflow.

Operating Properties:
Rated Voltage U0/U: 300/500V
Continues operating temperature: Flexible: -5~+90℃ 
                          Fixed: -40~+90℃

 

EMC XLPE Wind Energy Shielded Control Cables

EMC XLPE Wind Energy Shielded Control Cables

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:HELP PS3 POWER CABLE !!!!?
If you guys in Italy use the one that is a right side up version is this =D then you should be fine. If bot you can buy a replacement cable for like $20 at a game store or best but or something like that.
Q:Power cable question.?
Possibly on the BoxiT-200 that takes 12 to 19 volts at 3 amps, positive center. Read the printing on user manual, it gives the requirements. Most other Elmo projectors are plugged into an ac outlet.
Q:flucatuation when Plug off power cable in my Laptop compaq v3424tu?
Maybe the power management resetting the notebook after unplug the power. it's not reset the whole system, only adjusting into battery mode (long life). Commonly, the screen will blank a moment. it's normal. the setting can be found in Control Panel, Power Option.
Q:My xbox has a red light on the power cable?
Disconnect each and everything except for the wires behind television and likewise get rid of xbox 360 confusing force and insert back connect each and everything back in position. the project must be fastened If difficulty nonetheless keeps happening then its an illustration of having a clean ability adapter(cable container) For any more desirable questions about xbox 360 be at liberty to ask
Q:COMPUTER POWER SUPPLY SPECIALISTS I NEED HELP!?
That Xbox power supply cable is pretty cool! I've never seen those before. Ok, as for the power supply questions: Peak power is the maximum amount of power the unit can supply for a short period of time (a few seconds at most). A computer, during start-up, will use quite a bit more power than once it has achieved steady state. This is because drives have to spin up, semiconductors have to power up, etc. Once everything is up and running, the power draw drops to nominal or steady-state Sustained power is the amount of power the unit can supply non-stop. When purchasing a power supply, always give yourself leeway. If a supply indicates it is 650 watts sustained and 80% efficient (gotta look at that efficiency!) then it can supply 520 watts of power continuously. Even at that, I wouldn't want to run it past 450 - 475 watts continuously. 12v DC is the high rail on a power supply. Different parts of the computer require different voltages to operate. Drive motors typically need the 12v DC, where as memory needs less than 3 volts. A computer power supply has different rails or supply wires which supply the following voltages: +12 volts DC, +5 volts DC, and +3 volts DC (there are some others but those are the key ones). I don't know what the power requirements are for an Xbox 360, but it obviously needs the 12 volt and 5 volt DC rails to power it. Anyway, the power supply you've listed above is more than adequate.
Q:Home improvement, the wire specifications generally how to choose? Lighting, sockets, air conditioning with a few square lines? Ground specifications can be lighter than the line of fire, zero line?
You can use, but look at your LCD TV there is no DVI port or HDMI port, the best use of HDMI port or DVI port, the specific look at your TV size, if your TV support 1080P, it is best to use HDMI or D fans ridicule guest Piji nine Depends on the end VI, because the VGA can only 1080I can not 1080P, with HDMI or DVI display will be better.
Q:Ceiling on the wire after the tube is the tube on how to fix it on the ceiling?
Or with 6 points to the difference, but almost a few money, but you know when threading, 6 points is absolutely more effort, the line is also effort, the wire protection is also good!
Q:when you hook up a resistor to a power capacitor should it be at the end of the power cable?
It doesn't matter. You can put it before, after, beginning, middle, end. It doesn't matter.
Q:What are the varieties of wire and cable (detailed point)
DJ is a distributed instrument signal cable, also refers to the computer cable, V is PVC. The specific meaning can see the manufacturer's product description.
Q:How to join a power cable together?
You can install a plug on the cord to replace the one that was chewed off. Choose one with the same number of prongs as the cord has wires (2 or 3). Be sure to attach each wire to the correct terminal! Splicing the cord is also OK, and tape would not be a problem if applied properly, but I prefer to use heat-shrink tubing. When I do a top-grade splice, I first twist the wires tightly together without making a tail, then I solder them.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range