Ductile Iron PVC taper

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
1 Ton m.t.
Supply Capability:
500 Tons per Month m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

DI PCV Taper 

1. PVC fitting. 

2. Standards: BS EN12842

3. Ductile iron

4. ISO 9001 BV

 

DI PCV Taper

1. Material :    Ductile iron  DI PVC taper

2. Technique :  Lost foam casting technology(It is the most advanced technology in this field, so the quality of our products is much better than those using traditional casting.)

3. Standards :  BS EN12842

4. Certificate: ISO 9001 2008 and BV Product Conformity

5. Size  :     DN40-DN600

6. Fusion bonded epoxy coating

7. Flange drilled  :   PN110/ PN16/ PN25 according to BS4504

8. Socket joint  :   T type ( push-on type) / K type ( MJ type)

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the manual pre assembly procedure for the EO-2 joint?
I. pre assembled1, EMB card sleeve type pipe joint pre assembly of the most important link, directly affect the sealing reliability. A dedicated preprocessor is usually required. The small diameter can be pre joint in a vise. The concrete method is to use a joint as the mother's body and press the nut and the sleeve onto the tube. The utility model mainly comprises a sleeve type through pipe joint, a clamping sleeve type end through connection head, a clamping sleeve type three way pipe joint and other patterns. I found that even if the same manufacturer of a batch of goods, the cone of these joints on the depth of the hole is often different, resulting in a leak, and this problem is often neglected. The correct approach is to connect the end of the pipe with what kind of joint, and the corresponding connection ends are prefabricated with the same type of joint, so that the leakage problem can be avoided to the maximum extent.
Q:What does flaring pipe joint mean?
The joint is tapered and the pipe is straight, which requires the use of special tools to extend the end of the pipe to the bell mouth
Q:What's the difference between the half pipe joint and the branch seat?
The 1. half pipe joint standard half pipe joint specification production pipe connection form the connection form is divided into three kinds of socket weld connections, welded connections, threaded connections. Pressure rating: pipe pressure rating, general socket welding, butt welding fittings form the pressure rating of 3000LB (SCH80), 6000LB (SCH160), 9000 (XXS). Thread connection type, pipe pressure grade is divided into 2000LB, 3000LB, 6000LB. The commonly used pipe Name: 90 degree elbow, three, four, 45 degree oblique three, couplings (pipe joints, and copy), half coupling (half pipe joints, pipe cap, semi Bele), Union (by either), Taiwan Branch (branch block). The power plant took over the seat, forged three, threaded plug, the wire, bushing, strengthening pipe joint pipe.
Q:What do you mean by pipe joint 3/4-150?
It's not very clear. There may be an interface screw with a size of 3 / 4, 15 teeth, and a O ring
Q:Hot tap water pipe joint leakage, what method can be repaired?
If the water pipe is thicker, you can use the hot melt machine directly in the external welding, the gap will be blocked, this method can not have too high pressure.A solder gun can also be used to spray solder directly into the solder joint, which can be used with the PP-R patch.
Q:Hydraulic pipe fittings, DIN, GB, American Standard how to distinguish?
ZG is a commonly known as cone, cone thread processing, pipe joint is generally the old GB marked Rc for metric threads to represent the thread pitch, with every inch of the thread number, this is the biggest difference between them, metric thread is 60 degrees equilateral tooth type. 55 inch thread is isosceles tooth type of thread, 60 degrees. Metric units for metric threads; British and American systems. Pipe thread is mainly used for pipe connection, the internal and external threads are closely matched with straight pipe and cone pipe two kinds. Nominal diameter refers to the diameter of the pipe to be connected. Obviously, the diameter of the thread is larger than the nominal diameter. 1/4, 1/2, 1/8 is the nominal diameter of inch inch, inch in inches.
Q:Reinforced pipe joint,Used in chemical pipes
20# steel, JB 4726-2000 material "pressure vessel with carbon steel and low alloy" standard, SW socket welding.  40T025/01 is drawing number, SCH80 diameter specifications. See below;
Q:Hydraulic hose joint is spherical and cone sealing, threaded connection, what is the form of joint?
UNF often used to transport water (high temperature), the imperial teeth often used to transport oil (high pressure).
Q:Hydraulic hose connector size 20As shown in Figure six, the angle is 71mm to the edge, 80mm to the diagonal, approximately 34mm higher
Two. Metric general threads1. metric screw thread with a capital M, tooth type angle 2 degrees =60 (alpha tooth type half angle);2. metric ordinary thread by pitch, coarse teeth, ordinary thread and fine teeth, two kinds of ordinary thread;2.1. coarse tooth ordinary thread mark generally does not indicate the pitch, such as M20 means coarse thread; fine tooth thread mark must indicate the pitch, such as M30 * 1.5 for fine tooth thread, in which pitch is 1.5.2.2. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length.
Q:How do I distinguish the rigid clamp joint and the flexible clamp joint from the outward appearance?
The connecting bolts are different, and the flex is 2 larger than the rigidity (with 159 clamps as an example)The two semicircle butt joint is different, the flexible clamp is butt joint, and the rigid clamp is embedded butt joint
Takes customers' satisfaction as our goal, we contribute to our environment and society. Our company has a team of competent technicians and skilled workers, and wins customers' excellent promise and honor of the society because of good quality and satisfied service with six years' development. Our commitment to quality will ensure the continued success of our company.

1. Manufacturer Overview

Location Shandong,China (Mainland)
Year Established 2006
Annual Output Value
Main Markets Eastern Europe
Southeast Asia
Mid East
Eastern Asia
Western Europe
Company Certifications ISO9001:2008;BV Certificate For Product Conformity;China Credit Example Certifitcate

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage 71% - 80%
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size: 5,000-10,000 square meters
No. of Production Lines 5
Contract Manufacturing OEM Service Offered
Product Price Range