ductile iron pipe fitting

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Description :

1. Standards : ISO2531, ISO4422, EN545 , EN598 , BS4772 , AWWA C110

2. material : GGG500-7 or other Ductile iron .

3. coating : Fusion bonded epoxy coating ; cement lining inside and zinc primer and bitumen painting outside ; bitumen painting inside and outside ; red anti-rust coating .

4. package : wooden cases with plastic layer , wooden pallets with plastic layer , steel crates .

5. accessories such as gaskets , bolts and nuts available upon request .

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the categories of ductile iron pipe fittings?
But even if it is plastic and rotational, between the two in the process and the use of the effect also has the essential difference. Pipe fittings, usually coated with epoxy resin in ductile iron grooved pipe fittings. But this kind of pipe in the process without heat pipe trench because of rotational rotational adhesion as mature, its internal plastic heat pipe trench.
Q:How can the ductile iron pipe be punched?
Ball milled cast iron pipes can be opened and the opening size depends on the main pipe. For example, the main pipeline is DN100, diameter 118 milling pipe, can open the 100mm maximum aperture (with aperture opening), commonly used manual opening now the minimum 20mm, maximum 600mm, maximum 800mm hydraulic hole, open hole drilling machine dedicated
Q:How can ductile iron pipes be connected to steel tubes?
First insert a flange plate on the ductile iron pipe and then screw it with the flange on the weld pipe.
Q:How many kinds of elbow of ductile iron pipe?
There are 12.5 degrees and 22.5 degrees elbow, but manufacturers rarely produce. You can consult the manufacturer on the Internet
Q:Is the ductile iron pipe metal pipe?
Ductile iron pipes are metal tubes, because ductile iron is also a kind of metal. See the classification of metalsGenerally, metal materials are classified into two major categories: ferrous and non-ferrous metals
Q:Could you tell me how to weld ductile iron parts and steel tubes?
Disk or disk plug connection, it is best to use flange connection. First insert a flange plate on the ductile iron pipe and then screw it with the flange on the weld pipe. But note, because ductile iron pipe material is crisp, and the two connecting flange sealing surface is best all the plane, in order to prevent damage due to uneven iron flange.Material is different, ductile iron pipe is made of ductile iron, seamless steel pipe is made of structural steel. Such as No. 20 steel, No. 35 steel, 16Mn steel and so on. The two is the manufacturing process is also different, ductile iron pipe is generally sand casting molding; seamless steel pipe is made of billet through seamless steel tube mill hot rolling molding.
Q:How to improve the quality of nodular cast iron pipe fittings
To avoid the iron pipe inner wall of mold management lean reduce iron pipe pipe mould run speed, can make a dense and uniform pitting; avoid mold wall cast iron pipe pipe packed too shallow, increase the pressure, wear a good play to nod, can ensure the suitable depth of pitting.For pipes with grease and debris on the inner surface, especially the new cast iron pipe fittings, the grease and sundries on the surface of the cast iron pipe can be removed before use. For the cast iron pipe mould with a crack of a turtle, it is slight to use. When in use, the amount of mould powder should be increased; if the crack of the turtle is serious, the cast iron pipe mould must be replaced in time.
Q:How is the weight of nodular cast iron pipe calculated?
In the ferrite and pearlite matrix on the distribution of a certain number of spheroidal graphite, according to the nominal diameter and the elongation of different microstructure of ferrite and pearlite in different proportions of small caliber pearlite percentage is generally not more than 20%, large diameter of the general control in about 25%.
Q:How to inspect ductile iron pipe fittings?
On the quality of single pipe can analyze it from the surface is sand type and water cooled pipes, K8 pipe is different from Shanxi root nature is that the proportion of grade K9 cement and cast iron pipe and the K8 pipe are different, there is no national standard and non standard, no K8 tube, only is the production plant in order to obtain more profits, the dealer is not up to the national standard K9 grade pipe called K8 grade ductile pipe, K9 pipe cement weighs about 1/5 weight of the pipe, but is played in the role of anti-corrosion,
Q:Comparison of C and K grades of ductile iron pipes
C grade tube is the latest international standard for ductile iron pipes. The product standard is ISO2531:2009, which is compared with the original standard ISO2531:2003 class K pipe code. Pipe usage remains unchanged. But the new standard (C pipe) classification is based on the allowable work pressure grade of the pipe, while the original standard (grade K tube) is classified according to the pipe wall thickness grade.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range