Bubble pack for each valve. Outside packing are plywood cases. Or as per the request of customers.
Within 30 days after receiving T/T down payment.
Material : GGG50 Body&Bonnet/GGG50+EPDM Wedge/SS420 Stem/GGG50 Handwheel/PN16 Size:DN50-DN600
PN16 Non Rising&Rising Stem Ductile Iron Gate Valve DN50-DN600
The products are widely used in water source projects, urban water supply and drainage, sewage treatment, electric power, petroleum, petrochemical , heat supply, shipbuilding, medicine and metallurgy industries. Equipment are used for regulating or cutting off media in pipelines. Suitable media include water, sewage, sea water, air, foodstuff and oil. Suitable for gear operators, electric and pneumatic control actuators.
Send a message to us:
Q:Installation and operation instructions of knife gate valve
3., check the packing parts require compaction, not only to ensure the sealing of the packing, but also to ensure that the gate open flexible;4., before installing the valve, users must check the valve type, size and attention to the media flow direction, to ensure consistency with the valve requirements;
Q:What does gate valve Z41H-40 mean?
Z-- valve, 4-- connection, flange connection, 1-- structure, open bar wedge type rigid single gate valve, surfacing iron hard alloy h-- seal, 40- nominal pressure is 40 kg, which is 4.0MPa, the material is carbon steel casting
Q:Why does the centrifugal pump start and stop in the case of closing the gate valve?
Centrifugal pump to close the gate valve in the case of the start: the centrifugal pump power increases with its flow rate, when the flow is zero (valve closed), the minimum power to operate. Start the valve off from the angle of the motor. If the valve is started, the motor itself to start the current is larger, coupled with the power of the pump is also large, easy to cause the motor over-current trip, serious will burn the motor.
Q:Z41T one 10 gate valve and Z44T one, 10 gate valve difference
Z41T one, 10 is single gate, Z44T one, 10 is double gateAccording to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== connection: flange type1== structure: Rigid single gate4== structure: Rigid double gateT== sealing surface material: copper alloy10== pressure rating: 1.0MPa
Q:What does gate valve do?
The gate (gate valve) is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle.Gate valves for Class150 ~ 2500, the working temperature of -29 to 425 DEG C (Tan Gang) or -29 to 500 DEG C (stainless steel) small caliber pipeline, used to cut off or connect the line of medium, use different materials, can be separately applied to water, steam, oil, nitric acid, acetic acid, oxidizing medium, urea etc. a variety of media, the 3 Classification valve according to the different classification methods can be divided into: the parallel gate valve, wedge gate valve, valve lift, rotating rod valve, quick opening and closing valve, reduced valve, flat gate valve etc.. 4, characteristics of fluid resistance is small, applicable pressure, temperature range, medium flow direction is not restricted, good sealing performance
Q:What are the advantages and disadvantages of flat gate valves?
The advantage of flat gate valve is that the flow resistance is small, and the flow resistance is similar to the flow resistance of short valve. The flat gate valve with guide hole is installed on the pipeline and can be directly cleaned with the cleaner. As the gate is sliding on the two seat surface, the flat gate valve can be applied to the medium with suspended particles, and the sealing surface of the flat gate valve is actually positioned automatically. The seat seal surface is not subject to thermal deformation of the valve body. Moreover, even if the valve is closed in cold condition, the thermal elongation of the stem will not cause the seal to be subjected to overload. The length of the structure is much shorter than that of the ball valve, and it is easier to start. Light plate gate valve is more refined, but the effect is exactly the same.The disadvantage of flat gate valve is that when the medium pressure is low, the sealing force of the metal sealing surface is insufficient, so as to achieve satisfactory sealing. On the contrary, when the medium pressure is high, if the sealing surface is not lubricated by the system media or foreign media, often opening and closing may cause the sealing surface to wear too much. Another disadvantage is that the circular motion of the circular gate in the circular flow, only when it is at the valve closed position of 50%, this valve is more sensitive to flow control. Moreover, the gate will produce severe vibration when it breaks the high-speed and dense medium flow. The valve seat can also be throttled if the seat is made of a V - shaped opening and is tightly oriented to the gate.
Q:What's the meaning of flexible z45x-10q door valve?
Crown valve pressModel Z45X-10QZ refers to gate valve4 finger flange connection5 refers to the dark bar driveX refers to rubber seals10 refers to 10 kg pressureQ refers to the body material, ductile ironFull bore flange soft sealed gate valve
Q:What are the features and uses of the gate valve?
What is gate valve? What is the purpose of forged steel gate valves? What are the features of forged steel gate valves?Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The gate valve movement direction perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The gate has two sealing surfaces, and the two sealing surfaces of the most commonly used gate valves form wedge and wedge angles vary with valve parameters. Gate valve drive classification: manual gate valve, pneumatic gate valve, electric gate valve.DefinitionGate valve means the closing of the valve (gate) along the central line of the vertical direction of the valve. The gate valve is mainly used for cutting in the pipeline.The valve is a valve with a very wide, cutting device general caliber DN = 50mm use it, sometimes a small diameter cutting device also use valve, gate valve has the following advantages:Fluid resistance is small.Minor force needed for opening and closing.Medium flow is unrestricted.When opening fully, the sealing surface is eroded by the working medium smaller than the cut-off valve.The shape is relatively simple and the casting process is betterValve also has shortcomings:The overall size and opening height are larger. Larger space required for installation.In the process of opening and closing, there is relative friction between the sealing surfaces, which may cause galling.Gate valve generally has two sealing surface, processing, grinding and maintenance to increase some difficulties.
Q:Gate valve z45h-10dn250 length of the body?
Z45h-10dn250 body length L=330mm, this valve is hidden bar, elastic seat, sealing gate valve, gate lining, lining fluorine, belong to soft seal
Q:What is the size and length of the DN80 gate valve? 10 kg and 16 kg, respectively?
Valve structure length standards are PN16, short series for 203mm, long series for 280mm, flange size by PN16.