Q:What does "D41X-16" mean?

D butterfly valve, 41 flange connection, X rubber seal, 16 kg pressure

Q:How to connect the signal butterfly valve?

The signal butterfly valve should be the surveillance and alarm of human action. Once it is closed, it will alarm the system.Signal butterfly valve wiring method:1, open the switch box cover, according to the electrical control requirements, the cable core line to the corresponding terminal, and sealed cable imports, while the cable fixed, to prevent external force damage when the cable wiring.2, when the valve in the "closed" position, the clockwise rotation of the following relationship to the cam is just touch micro switch cam (you can hear the clicking sound), and then tighten the screw on the cam cam.3, when the valve in the "fully open" position, counterclockwise turn the upper open cam, with the same method to adjust the open cam.4, adjust the limit screw, when the valve in the "full off" or "open" position, should not make the limit screw just at the top of the worm gear limit plane, and should have a certain gap, and then tighten the lock nut on the screw.5, on the cover of the electrical switch box cover, when the valve in the "off" position, the pointer opening indicator to dial "0" scale, and tighten the screws pointer.

Q:What are the advantages of butterfly valves?

B. is cheap, especially when the caliber is big;C. the resistance loss is small and the fluid decreases through pressure;

Q:Butterfly valve D71X-1.6C, DN50, there is no difference between C and no C? What do you mean by "concrete"?

The C indicates that the material is carbon steel and does not indicate cast iron (generally omitted)

Q:I HAVE A 2003 FORD EXPEDTION THAT IS IDLE ROUGH,AND WILL EVENTUALLY STALL. TODAY I FOLLOWED THE PCV VALVE HOSE TO THE BACK OF THE THROTTLE BODY AND NOTICED THERE IS A BIG HOLE ON THE ELBOW OF THE HOSE. HOW CAN I CHANGE IT? CAN I JUST FORCE THE HOSE OUT AND SIMPLY PUT A NEW ONE? BEEN HAVING THIS ROUGH IDLE /STALL PROBLEM FOR A WHILE I CLEANED IAC VALVE, THROTTLE BODY CHANGED THE AIR FILTER AND ALSO CLEANED THE MASS AIR FLOW SENSOR, I HAVE A P0171 system to lean(bank 1) code

just undo the clamps, and pull. it may need some wiggling and tugging, as its been on there for 9 years now without moving. put on your new hose, and replace the clamps, and youre done. next time, try not using all caps. it doesnt make us want to answer your question anymore just because its in caps, in fact, maybe a little less.

Q:butterfly valves d7a1x5

D71x-1.6? Or D371X-1.6, do you need butterfly valves for production or butterfly valves? The question perplexed us all.

Q:can't locate freon intake valve for 03 jaguar an was wondering were it is located at

There is no Freon intake valve for an 03 Jaguar. Freon is R12 refrigerant and the vehicle uses an R134a refrigerant system. There is also no such thing as an intake valve on any vehicle refrigerant system. There is a high pressure port and a low pressure port. To answer your question: under the hood. Any other information would likely endanger your life, since this is obviously a DIY question and you lack the knowledge to safely recharge your vehicle's refrigerant system. R134a refrigerant, if inhaled, can kill you. Do not turn a DIY project into a DIE project. Leave the complicated stuff to the professionals.

Q:How many kinds of butterfly valves are there?

[main classification]1, according to drive points(1) electric butterfly valve(2) pneumatic butterfly valve;(3) hydraulic butterfly valve;(4) manual butterfly valve;2, according to the structure of the form:(1) Central sealed butterfly valve(2) single eccentric sealed butterfly valve(3) double eccentric sealed butterfly valve(4) three eccentric sealed butterfly valve;3, sealing surface material quality:(1) soft sealing butterfly valve.1) the sealing pairs are made of non-metallic soft materials, which are made of non-metallic soft materials.2) the sealing pair is made of metal hard material and is made of non-metallic soft material.(2) metal hard sealing butterfly valve. The sealing pair is made of metal hard material and is made of metal hard material.4, according to sealed form points:(1) forced sealing butterfly valve.1) elastic sealing butterfly valve. The pressure of the valve seat, seat, or plate is produced when the seal is closed by the pressure from the valve.2) additional torque seal butterfly valve. The seal is produced by a torque that is applied to the valve shaft.(2) pressure sealed butterfly valve. The pressure is greater than the pressure on the seat or plate.(3) automatic sealing butterfly valve. The pressure of the seal is automatically generated by the pressure of the medium.

Q:What's the difference between D71X-16 and D71H-16 butterfly valves?

D71X-16 and D71H-16 butterfly difference is that the cut-off is not the same, the latter is stainless steel seal, corrosion resistance, friction, acid or impurities can be medium fluid. The former is rubber sealed, only through the general temperature of the medium, not acid, with more, you can ask Luoyang crown Ning

Q:What's the difference between a clip on handle butterfly valve and a turbo butterfly valve? Where are they used?

1, the drive mode is different (handle or turbine), mainly based on the size of the valve and the opening and closing torque to decide.2. The butterfly plate of the worm valve is installed in the direction of the diameter of the pipe. In the butterfly valve body cylindrical channel, the disc shaped butterfly plate revolves around the axis, the rotation angle is 0 degrees ~90 degrees between, when rotates to 90 degrees, the valve opens the card completely.3, clip type butterfly valve is to use double headed bolts to connect the valve between the two pipe flanges, flange butterfly valve is a valve with a flange, bolt with the valve flange at both ends connected to the pipe flange.