Q:How do hydraulic butterfly valves work?

3. butterfly valve hydraulic drive device structureThe valve hydraulic device is mounted on the valve drive shaft. The driving shaft of the valve is fixed with a transmission spline, and the crank (with an outer spline) is sleeved on the driving shaft. When the hydraulic system works normally, through the gear sleeve, the transmission spline is connected with the crank. Thus, the hydraulic cylinder drives the crank, and the spline on the crank passes the torque to the transmission spline by means of a gear sleeve. Because the driving spline is fixed on the driving shaft, the driving shaft rotates and drives the valve plate to start and close. A section of optical axis is arranged at the end of the driving shaft and is inserted into the end of the manual shaft (matched with the clearance of H11/ H11), and the function is that the manual shaft is concentric with the main drive shaft. In normal operation, the optical axis rotates with the drive shaft, but the manual device does not move. When the hydraulic operation is performed manually or manually from the hydraulic unit, a * * * conversion is required. The utility model is composed of a nut, a hand wheel, a screw rod, a support frame and a shifting device. When the utility model is switched, the hand wheel is rotated and driven by the screw rod to move. A guide rod is arranged on the bracket to make the shift and translation stable.

Q:How to control the single acting pneumatic butterfly valve?

Single acting pneumatic butterfly valve, Luoyang crown butterfly pneumatic butterfly valve, mainly divided into two types of normally open and normally closed. What kind of effect do you want to achieve?

Q:Butterfly valve sealing material has several?

Nine: X1 (natural food gum), X2 (Heipalen), X3 (ethylene propylene rubber), X4 (neoprene), X5 (Ding Qing X6 (rubber), wear-resistant rubber (FPM), X7), X8 (silicon rubber), X9 (heat resistant ethylene propylene rubber)

Q:What are the butterfly valves models?

Divided by way of drive(1) electric butterfly valve(2) pneumatic butterfly valve;(3) hydraulic butterfly valve;(4) manual butterfly valve;In the form of structure:(1) Central sealed butterfly valve(2) single eccentric sealed butterfly valve(3) double eccentric sealed butterfly valve(4) three eccentric sealed butterfly valve;

Q:Butterfly valve common faults and treatment methods?

Three, summary:Only familiar with every detail of circulating water pump outlet valve and butterfly valve equipment, timely and thorough maintenance and strict debugging, to ensure the safety and reliability of equipment operation, to ensure the healthy and orderly operation of equipment.

Q:What kinds of butterfly valves are available? What is the working principle of butterfly valves?

At work temperature:(1) high temperature. T>450 degrees C butterfly valve.(2) medium temperature butterfly valve. 120 C<t<450 DEG butterfly valve.(3) normal temperature butterfly valve. A 40C<t<120 degree C butterfly valve.(4) low temperature butterfly valve. One 100<t< one, 40 degrees C butterfly valve.(5) ultra low temperature butterfly valve. T< one 100 degrees C butterfly valve. Www bgfm /df/Divided by connection:1 pairs of clip butterfly valveThe butterfly plate of the clip butterfly valve is installed in the direction of the diameter of the pipe. The valve is fully open.The clip butterfly valve is simple in structure, small in size and light in weight. Butterfly valve has an elastic seal and metal seal two types of seals. Resilient sealing valve. The sealing ring can be mounted on the valve body or attached to the periphery of the disc.2, flange butterfly valveThe flange butterfly valve is a vertical plate structure, and the stem is a sealing ring of an integral metal hard sealing valveFor flexible graphite plate and stainless steel plate composite structure, mounted on the valve body, butterfly plate sealing surface of stainless steel surfacing. The sealing ring of the soft sealing valve is made of nitrile rubber and is mounted on the butterfly plate.3, lug butterfly valve4 、 welded butterfly valveWelding type butterfly valve is a non sealed butterfly valve, widely used in medium temperature less than building materials, metallurgy and mining, electric power production process at 300 nominal pressure 0.1Mpa pipe, used to open and close connected, or adjust the medium quality.

Q:That industry uses most of the butterfly valve, and only use the butterfly valve, a large number of use of butterfly valve, seek expert advice!

Large diameter heating pipes with more than butterfly valves, greater than or equal to DN600 are used butterfly valve

Q:What type of valve does the butterfly valve D343X DN300 represent?

D butterfly valve, 3 worm gear, 4 flange type, 3 should be three eccentric X body, sealing surface for rubber, DN300 caliber 300MM

Q:What is the difference between the installation and function of a butterfly valve and butterfly valve?

The principle of the valve gate valve is open and close cases, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. Gate has two sealing surface, the most commonly used mode gate valve of the two sealing surface forming wedge, wedge angle with valve parameters vary, usually 50, medium temperature is not high when 2 degrees 52. Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate. Valve closed, the sealing surface can only rely on medium pressure to seal, that is to rely on medium pressure to the gate sealing surface pressure to the other side of the seat to ensure the sealing surface seal, which is self sealing. Most of the valve is forced seal, that is, when the valve closes, to rely on external force to force the gate to the seat, in order to ensure the sealing surface sealing. Gate valve with the stem along with a straight line of motion, called the lift rod gate valve is also known as the bar gate valve. Usually there is a trapezoidal thread on the lifter. The rotating motion is changed into a straight line through the nut at the top of the valve and the guide groove on the valve body. That is to say, the operating torque is changed into the operating thrust. When opening the valve, when the gate lift height is equal to 1:1 times of the valve path, the passage of the fluid is completely unblocked, but at run time, this position is unable to monitor. In actual use, the top of the stem is used as a sign, i.e., the open position, as its fully open position.Temperature changes appear to consider locking phenomenon, usually open to the vertex position, and then rewind 1/2 1 circle, as a fully open valve position.

Q:What's the difference between the three eccentric butterfly valve and the two eccentric butterfly valve?

The structure features that the center of the stem deviates from the center of the disc as well as the center of the body. The effect of the double eccentric valve can be opened immediately after the disc from the valve seat, substantially eliminating the unnecessary disc and valve seat over squeezing, scratching phenomenon, reduce the resistance from the open, reducing the wear and improve seat life. Three eccentric butterfly valve: to high temperature, must use hard seal, but the leakage is large; to zero leakage, must use soft sealing, but not high temperature. In order to overcome the double eccentric butterfly valve this contradiction, and the butterfly valve for third times eccentric. The so-called third eccentric, that is, the shape of the sealing pair is not a positive cone, but rather oblique cone.