Specifications of Ductile Iron Double Socket Taper For Push-on Joint
1. Material: Ductile Iron GGG50 or others
2. Standard: ISO2531, EN545, BS4772, AWWA
3. Size: DN40-DN2000
4. Pressure: PN10, PN16, PN25
5. Surface: Fusion Bond Epoxy Coating, Zinc primer & ciment lining and Bitumen Painting
6. Gaskets: EPDM/SBR/NBR
7. Accessories: Bolt, Nut and Gasket as per your inquiry.
8. Mechanical Properties: Tensile Strengh: ≥420 MPA; Elongation: ≥5%; Hardness: ≤250HB; Yield strength: ≥300 MPA
9. Hydrostatic Test Pressure: DN 80mm-DN 300 mm: 25 bar; DN 350-DN 600 mm:16 bar
Applications of Ductile Iron Double Socket Taper For Push-on Joint
Much of the ductile iron pipe fitting are used for water and sewer lines, including double flanged duckfoot 90 degree bend ISO2531 with best price. It is stronger and easier to tap, requires less support and provides greater flow area compared with fittings from other materials.
Packaging & Delivery of Ductile Iron Double Socket Taper For Push-on Joint
Packaging Detail: Wooder pallets, Container
Delivery Detail: According to detailed order quantity
Payment Terms of Ductile Iron Double Socket Taper For Push-on Joint
Usually the payment term we do is T/T 30% advanced, after received the copy of the documents and B/L the buyer pay the rest 70% of the total payment. After received all the payment, we mail the original documents with B/L to the buyer.
We also accept D/P at sight and L/C at sight.
It does not mean that we do not accept any other payment terms. We can offer other payment terms based on your requirments after discussed and agreed. So any inquires about payment terms are welcome to be disscussed with us.
It is important to note that different payment terms means different price!
According to your requirement, we are ready to serve you at best quality and competitive price on every product. If you have some interests, please contact us at any time. We’ll give you an early reply!
- Q:Man, can you send me some national standards? Mainly for hydraulic use
- SN751877752732807887883882884832789865455591The joint SN807 head can be placed behind the standard, behind pick up my personal often replaced welding; because the domestic expansion connecting pipe, surface finish is not enough, easy to pick up leakage; and in the process of construction workers often pick up badly, also easy to leak.
- Q:Stainless steel pipe, wire joint leakage how to make up?
- 1) want to save trouble, buy special glue to block, general hardware store can buy;2) the silk joint opens, the more winding some raw rubber tape, then turns tight to see whether can solve the problem;3) if it is a silk joint, replace the wire joint;4) the pipe is re tapped or replaced with a new pipe;
- Q:Silicone gasket, rubber gasket, water pipe joint which is good?
- More suitable for food grade high water pipe, especially high temperature resistance, high temperature water pipe is best to use silica gel gasket
- Q:Reinforced pipe joint，Used in chemical pipes
- D means "diameter", and "n" means "internal" (because pinyin is "Nei" in "inner")
- Q:110 degree PVC pipe joint
- Hello, you can use PVC two to a 45 degree elbow three back, try on the line, 35 meters of pipe according to the 1% grade to install, depends on the specific circumstances if the flow rate is larger and with construction conditions if the proposed slope is a little bigger. (personally) I don't think it's necessary to install it with stainless steel pipe
- Q:The pipe line of the hydraulic pressure pipe is formally installed
- 2.2. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length;3.1. commonly used metric ordinary coarse thread pitch as shown in the following table (threaded hole diameter: carbon steel = nominal diameter P = nominal diameter cast iron; 1.05~1.1P; processing thread rod diameter = nominal diameter: 0.13P):Table 1 diameter / pitch of common metric coarse tooth threadThe nominal diameter of P cast iron bottom steel bottom thread rod diameter pitch P cast iron bottom bottom rod diameter of external thread steel
- Q:Type parameter of pipe joint
- 1/8 SS-MC-TF5-NT2 1.34 0.38 0.73 0.64 0.19 9/16 5/8 1.05 5/16* 1/4 SS-MC-TF5-NT4 1.52 0.56 0.73 0.64 0.25 9/16 5/8 1.23 3/8 1/8 SS-MC-TF6-NT2 1.39 0.38 0.76 0.66 0.19 5/8 11/16 1.10 3/8 1/4 SS-MC-TF6-NT4 1.57 0.56 0.76 0.66 0.28 5/8 11/16 1.28 3/8 3/8 SS-MC-TF6-NT6 1.57 0.56 0.76 0.66 0.28 11/16 11/16 1.28 3/8 1/2 SS-MC-TF6-NT8 1.82 0.75 0.76 0.66 0.28 7/8 11/16 1.53
- Q:Infusion, infusion tube joints fall off and immediately connected, lost three or four minutes will have an impact?
- First of all, this approach is wrong, is not allowed, and if it is medical staff to get, then he is not standardized, there is no sterile concept, such as the patient is self made, then he is ignorant, do not understand.Secondly, it has no contact with other things off, did not meet, but also to avoid forcibly, if encounter, after losing what no adverse reactions often have no major obstacles to the body, but the poor resistance of the people, the consequences can be little.
- Q:Can the sleeve type pipe joint be disassembled and assembled several times?
- The European and American card sleeve pipe joint is a standard part, it can be disassembled and assembled many times, but it is better to check the sealing cone into the pipe, whether the inner component has the wrong face, the pipe is better to choose the new connection.
- Q:How many bonding methods are there in the belt joint?
- 3. heat curing joint, the heat vulcanizing joint conveyor belt interface is completely closed, not susceptible to water wetting. Technology of belt vulcanizing joint is generally placed on the belt vulcanizer frame under the frame, both ends of the alignment, then put on the pressure plate, small thermal insulation board, insulation sheets, two vulcanizer installed on each side of 1-2 meters of the platform and fixed platform, the upper surface to the lower heating plate and flat surface homogeneous or slightly lower, also cannot affect the tension rod, the belt joint two on the platform began to cure. This method is a kind of joint is the best method that can guarantee the high coupling efficiency, but also very stable, joint life is long, easy to master, but the heat curing joint process is relatively complex, high requirements for personnel, cold bonding process is simple and short-term training posts.
SUPERFITTING,a large and professional manufacturer for ductile iron fittings for water pipelines in China, imported production technology of vacuous lost foam casting from Japan with high-tech production lines and modern inspection equipments. Products for overseas markets covered all over the world.
1. Manufacturer Overview
|Annual Output Value
||Above US$ 13 Million
||Mid East, Africa, Europe
||ISO 9001:2008; ISO2531:1998
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
||English; Chinese; Spain; Alabic
||Above 6500 square meters
|No. of Production Lines
||OEM Service Offered; Design Service Offered
|Product Price Range