Ductile Iron Butterfly Valve Of Top Quality Made in China

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
50 set
Supply Capability:
1000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1. Manual Wafer Butterfly Valve Description

A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.

 

2.Main Features of the Manual Wafer Butterfly Valve 

a)Cast hole. Flange connection meet ANSI 125/150#   DIN PN10/16   BS4504 PN10/16 in the meanwhile.

 

b)Soft seat. Replaceable. Increase of service life.

 

c)Double half shaft without pin.

 

d) Square and short neck. Easy to stick scutcheon and cost saving.

 

3. Manual Wafer Butterfly Valve Images

 Ductile Iron Butterfly Valve Of Top Quality Made in China

Ductile Iron Butterfly Valve Of Top Quality Made in China

4.Manual Wafer Butterfly Valve  Specification

 a) Body: CI(cast iron ,GG25 )/ DI (ductile iron ,GGG40)

b) Disc:  DI / CF8 / CF8M / C95400 
c) Seat:  EPDM / NBR / TEFLON / VITON

 

5.FAQ

 

1. What is manual wafer butterfly valve?

A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.

 

2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.

 

3. What is the working principle of manual wafer butterfly valve?

 A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do you calculate the valve wall thickness, pressure, and other valve design calculations in a spreadsheet?
For you to introduce the spreadsheet calculation, application basis, you according to this principle for valve correlation calculation:When A1 and B1 cells are used as parameters, the amount of computation is calculated by C1. If the formula is X+Y=? In the A1 cell, fill in the X; fill the Y in the B1 cell; fill in the C1 cell with "=A1+B1"; enter the carriage, and then calculate the corresponding value in the C1 cell. For example: fill in 5 in the A1 cell; fill in 8 in the B1 cell; enter the carriage, and then appear in the C1 cell 13. Other calculations are the same, you will calculate the valve formula, such as the above fill in, given the corresponding parameters, the same can be calculated.
Q:What is the purpose of the valve?
Valve is a pipe accessory. It is a device used to change the direction of the passage and the direction of the medium flow, and to control the flow of the conveying medium.Valves have the following uses:1. Connect or cut off the medium in the pipe. Such as gate valve, globe valve, ball valve, plug valve, diaphragm valve, butterfly valve and so on.2 、 adjust and control the flow and pressure of the medium in the pipeline. Such as throttle, control valve, pressure reducing valve, safety valve, etc..
Q:How can I install the water pipe valve?
The new spool to buy off, installed in the old spool that. You don't have the same brand. You may not be able to load it. It's better to have the same brand
Q:Our company is doing valve exports,
First of all, you have to check the HS encoding of your product.The corresponding HS code will have a regulatory condition followed by different regulatory conditions that mean different procedures (or certificates), such as what you call "B".What aspects must be examined in commodity inspection?Different products to implement different inspection and quarantine methods, the general is to do a customs clearance on the OK. The products you mentioned above may not need to do customs clearance (see what kind of valve you are, so you'd better check the conditions again)Is commodity inspection agent or business enterprise? Do you need to check every export?Generally not many agents are on the line, and if the HS regulatory conditions have to do customs clearance, then each time to do.Is there any standard or basis for inspection? Where can I find out the knowledge in this area?
Q:What is the valve before and after the pump?
Conventional setting, the pump is installed before and after the cut-off valve. As for the check valve, according to the need to decide whether to install, to see whether the occasion required to prevent backwater function.
Q:How does the valve open?
Turn the valve counterclockwise, turn clockwise, or turn left, right and leftYou turn the valve to the left.
Q:Representation of several types of valves
Valve type:Z gate valveJ stop valveL throttling valveQ ball valveD butterfly valveH check valve and bottom valveG diaphragm valveA safety valveT regulating valveX plug valveY pressure reducing valveS trapDZ solenoid valveO electromagnetic motionDrive mode:1. electromagnetic and hydraulic action2., electricity, a liquid3. worm gear4. the spur gear rotates5. bevel gear rotation6. pneumatic7. fluid movement8. air and one liquid movement9. electricOther hand wheel, handle, board hand, no performanceSide mode;1. internal thread2. external thread3. flanges (for double spring relief valves)4. flanges5. flanges (for lever type, safety door, single spring safety door)6. welding7. pairs of clips8. clamps9. card sleeveIllustrated cover or lining:T copper alloyH alloy steelB tin based shaft (bearing alloy)Y cemented carbideX rubberJ hard rubberSA PTFESB poly three fluoro ethyleneSC polyvinyl fluorideSD phenolic plasticsSN nylon
Q:Is there any problem with connecting the geothermal valves with other geothermal pipes?
Yes, as long as it's all PPR's.Material is the same, the fuse will not cause shrinkage when you can use
Q:What are the other valves used for the control of dual-use items?
That is to say, your valve needs to be used as dual-use items and technology import and export licenses. Shanghai import and export can find me. We have electronic keys for dual-use items
Q:Where is the Hefei valve market?
On the valve network to find the best, you can find the valve business in Anhui

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range