Double spigot with puddle flange fitting

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

ductile iron piep fittings with epoxy painting by flanged under ISO2531

Standard:

ISO2531 EN545

Size

DN80-DN2600 PN10/16/25


Connecting Mode:

Flanged, socket, Mechanical Joint, Loose Flanged


Coating:

Inside lined cement and outside painting with zinc plus bitumen

Inside and outside painting with epoxy


Accessories:

Rubber gasket, a complete set of bolt



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How can ductile iron pipes be connected to steel tubes?
Disk or disk plug connection, it is best to use flange connection.
Q:How much is the installation of a two degree elbow for ductile iron pipe fittings at 11.25 degrees?
The main components of ductile iron pipes are carbon, silicon, manganese, sulfur, phosphorus and magnesium. In the ferrite and pearlite matrix on the distribution of a certain number of spheroidal graphite, according to the nominal diameter and the elongation of different microstructure of ferrite and pearlite in different proportions of small caliber pearlite percentage is generally not more than 20%, large diameter of the general control in about 25%. Minimum tensile strength: 420/Mpa, minimum yield strength 300/Mpa, minimum elongation 7%.
Q:How can the ductile iron pipe be connected to the PE pipe?
Cast iron pipe and PE pipe is connected with a lot of what is the most secure connection, flange connection (PE flange head + anticorrosive steel flanges + rubber gasket).
Q:How can the ductile iron pipe be punched?
Ductile iron should be drilled, the key is to see how big holes. If it is a small hole, you can consider using a small drill around 5mm to slowly wear the pipe, and then gradually reaming. If the fight is relatively large hole, may according to the aperture required first hit a circle hole, and then use a small chisel chisel down, slowly put the plate again to be trimmed. When drilling, add a little oil to cool the drill bit.
Q:How to improve the quality of nodular cast iron pipe fittings
To avoid the iron pipe inner wall of mold management lean reduce iron pipe pipe mould run speed, can make a dense and uniform pitting; avoid mold wall cast iron pipe pipe packed too shallow, increase the pressure, wear a good play to nod, can ensure the suitable depth of pitting.For pipes with grease and debris on the inner surface, especially the new cast iron pipe fittings, the grease and sundries on the surface of the cast iron pipe can be removed before use. For the cast iron pipe mould with a crack of a turtle, it is slight to use. When in use, the amount of mould powder should be increased; if the crack of the turtle is serious, the cast iron pipe mould must be replaced in time.
Q:Is the ductile iron pipe metal pipe?
Ductile iron pipes are metal tubes, because ductile iron is also a kind of metal. See the classification of metalsGenerally, metal materials are classified into two major categories: ferrous and non-ferrous metals
Q:Comparison of C and K grades of ductile iron pipes
Using more than 18 cast iron, after adding the spheroidizing agent, the centrifugal casting of ductile iron machine caused by high-speed centrifugal tube, known as "ductile iron pipe."".
Q:Connecting process of ductile iron pipe spigot and socket rubber ring
Rubber seal ring is formed by one or several parts of the cover, fixed in a ring or a washer bearing and another ring or gasket contact or the formation of the labyrinth of narrow gap, to prevent leakage of lubricating oil and foreign matter.
Q:Is the cast iron tube the same as the ductile iron pipe?
You are mistaken in concept. The cast iron pipe is the sort of connection method. The ductile iron pipe is classified according to the material.
Q:Could you tell me how to weld ductile iron parts and steel tubes?
Disk or disk plug connection, it is best to use flange connection. First insert a flange plate on the ductile iron pipe and then screw it with the flange on the weld pipe. But note, because ductile iron pipe material is crisp, and the two connecting flange sealing surface is best all the plane, in order to prevent damage due to uneven iron flange.Material is different, ductile iron pipe is made of ductile iron, seamless steel pipe is made of structural steel. Such as No. 20 steel, No. 35 steel, 16Mn steel and so on. The two is the manufacturing process is also different, ductile iron pipe is generally sand casting molding; seamless steel pipe is made of billet through seamless steel tube mill hot rolling molding.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range