Q:There are several kinds of tape knowledge

According to the scope of application division can be divided into:Warning tape, carpet tape, electrical tape, protective film tape, winding tape,Sealing tape, die cutting adhesive tape, etc..4, according to market penetration rate can be divided into: ordinary adhesive tape, special adhesive tape.5, according to the application of environmental temperature division can be divided into: low temperature tape, room temperature tape, high temperature adhesive tape.

Q:How do you apply double-sided adhesive tape?

1, we put the plate, tape and paste roller at the same room temperature for a period of time before pasting;2, in the paste version, it is necessary to press the plate and affixed to the cylinder clean;3 if the plate is attached to the sleeve, the minimum air pressure must be used to prevent the sleeve from deforming;

Q:What type of tape do you use for paint marking test?

8, 3M water labeling labels warranty and safety tape: 3M5557,3M5557NP, 3M5558,3M55599, 3M metal foil tape: 300PL, 508SN10, 3M grounding heat sink adhesive film: 737311, 3M conductive copper foil tape: 3M118111821183119411881189124513452245324512, 3M conductive aluminum foil tape: 3M112011701172117811791267, AL-25BT, AL-50BT, AL-25DC, CEA-1, CEA-213, 3M electromagnetic wave absorbing materials: 3M, AB2000, AB5000, AB6000, AB7000

Q:What are the general use of double-sided tape?

Oily double-sided adhesive, mainly used in leather goods, pearl cotton, sponge, shoes products, such as high viscosity. Embroidery double-sided adhesive mainly used in computer embroidery.Computer embroidery special, sticky strong, repeated use more frequently.

Q:Classification of base material of double sided adhesive tape

Hot melt double-sided adhesive mainly used in stickers, stationery, office and so on. Oily double-sided adhesive, mainly used in leather goods, pearl cotton, sponge, shoes products, such as high viscosity. Embroidery double-sided adhesive mainly used in computer embroidery.

Q:Double sided tape how to cut well, master with automatic cutting table, cut out, all askew, what reason, what should pay attention to?

First, the gap between the paper tube and the tube shaft is larger, so that the adhesive tape is generated during the rotation. Two, the number of yards is too large, 6MM width is best not more than 30Y.

Q:The basic requirements, attached to the bottom surface of the base, a bottom surface with a permanent adhesive, affixed to the side of the desktop environment. When the base is fixed with double adhesive, another part is inserted in it, and the component is required to be picked up from the vertical direction (>=15N), and the base is firmly jointed with the table top. But when the base needs to be repositioned, it can not be too difficult to pull out, and it can not destroy the structure of double faced adhesive, thus shortening the service life

In summary, you need to confirm the color of tape thickness is, the basic requirements, the substrate adhesive area, rework times and time.

Q:Construction method of butyl adhesive tape

Single sided non-woven fabric, Yongxing adhesive tape, method of use(1) after the lighting board is installed on the frame, the lighting board seam will be bound and the parts of the adhesive tape will be wiped clean.(2) open the adhesive tape in the joint of the lighting board, then tear off the insulating paper on the edge of the compacted adhesive tape, and then install the aluminum alloy board on the lighting board. Secure with a waterproof screw.(3) on the lighting board and the wall joint, use one side aluminum foil adhesive tape to bond directly. 1, construction requirements(1) the performance indexes of tapes should be read carefully before construction so as to be suitable for the environmental temperature and humidity during construction.(2) according to different waterproofing membrane, different construction methods, choose different types, specifications of different sizes of Yongxing tape.(3) before construction, the quality of the aforesaid project shall be checked and accepted, and the waterproof layer shall be constructed after qualification.(4) according to the requirements of the engineering design and construction waterproofing, waterproofing and leveling layer bonded firmly, do not allow Konggu phenomenon, after the construction of waterproof layer should be protected.(5) the use of Yongxing parapet should pay attention to the tape, brick or concrete surface bonding parts of the firm and smooth surface, such as the poor, the application of cement paste for repairing yarn

Q:The double-sided adhesive thickness 0.05~3mm, similar to A3, the A4 paper size? One by one?

Thickness: 90U, width: 0.6CM. This is a brand, a model of double-sided adhesive specifications, manufacturers of different, different processes, products are not the same.

Q:The foam on the wall will not tear off the double foamIt is convenient to ask for a rib

4, you can try a rubber. But in the beginning may feel more and more dirty, but rub a little longer, you will see the effect, this method is relatively tired, have perseverance.5, with blisters, put a little detergent, and then brush with an old toothbrush just fine.6, with a cloth with alcohol or Erguotou wipe.7, with a letter of sodium and water a wipe off, or can also use paint thinner.