DN600 Turbine Type Butterfly Valve with Hand wheel BS Standard
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
General valve using the market long-term, widespread Water Leakage, rust phenomenon, soft sealing gate valve produced by the introduction of foreign advanced technology of the enterprise. To overcome the poor sealing gate valve, general elastic fatigue, rust and other defects. Soft sealing gate valve is a traditional valve replacement products, the compensation effect of using flexible gate produce small deformation, achieve good sealing effect, the valve has a light switch, reliable sealing, good elastic memory and long service life and other significant advantages, can be widely used in water, sewage, construction, food, medicine, metallurgy, electric power, textile, energy systems, fluid pipeline regulation and closure devices as.
The characteristics of:
- flat style seat
The traditional control valve often pass after washing due to foreign objects such as stone, wood, cement, paper, and other debris deposited on the valve at the end of the groove. Close but not close easily lead to the formation of Water Leakage phenomenon, the lower part of the soft sealing gate valve with water using the same flat design, easy to siltation caused by debris, the fluid unimpeded.
And the overall package glue
The valve plate is made of high-quality rubber overall, the outsourcing of plastic, making the domestic first-class rubber vulcanization vulcanization after the valve plate to ensure accurate geometry, and the rubber and ductile iron gate is connected firmly, not easy to fall off and good elastic memory.
And corrosion resistance
The valve body adopts epoxy coating powder, can prevent the corrosion and rust, and can be used for sewage systems.
And not easy to break
Traditional cast iron garden gate often hit foreign objects, collision or overlap caused by the fracture phenomenon. Because the valve to switch to ductile iron, this is the case already significantly reduced.
Three "O" ring seal
As the valve stem with three "0" ring ring seal design, can reduce friction when the switch is greatly reduced, Water Leakage phenomenon and can cut off the water supply construction not replace sealing ring.
And help to drink
Due to the internal body to non-toxic epoxy resin coating, gate of the inner and outer surfaces are completely coated with rubber and can not rust or corrosion of water available to drink.
- Casting valve
Valve body casting, precise geometry makes the body without any internal finishing to ensure that the valve seal.
And light weight
The valve is made of ductile cast, lighter in weight than conventional gate weight about 20%-30%. Convenient installation and repair.
Overview:
General valve using the market long-term, widespread Water Leakage, rust phenomenon, soft sealing gate valve produced by the introduction of foreign advanced technology of the enterprise. To overcome the poor sealing gate valve, general elastic fatigue, rust and other defects. Soft sealing gate valve is a traditional valve replacement products, the compensation effect of using flexible gate produce small deformation, achieve good sealing effect, the valve has a light switch, reliable sealing, good elastic memory and long service life and other significant advantages, can be widely used in water, sewage, construction, food, medicine, metallurgy, electric power, textile, energy systems, fluid pipeline regulation and closure devices as.
The characteristics of:
- flat style seat
The traditional control valve often pass after washing due to foreign objects such as stone, wood, cement, paper, and other debris deposited on the valve at the end of the groove. Close but not close easily lead to the formation of Water Leakage phenomenon, the lower part of the soft sealing gate valve with water using the same flat design, easy to siltation caused by debris, the fluid unimpeded.
And the overall package glue
The valve plate is made of high-quality rubber overall, the outsourcing of plastic, making the domestic first-class rubber vulcanization vulcanization after the valve plate to ensure accurate geometry, and the rubber and ductile iron gate is connected firmly, not easy to fall off and good elastic memory.
And corrosion resistance
The valve body adopts epoxy coating powder, can prevent the corrosion and rust, and can be used for sewage systems.
And not easy to break
Traditional cast iron garden gate often hit foreign objects, collision or overlap caused by the fracture phenomenon. Because the valve to switch to ductile iron, this is the case already significantly reduced.
Three "O" ring seal
As the valve stem with three "0" ring ring seal design, can reduce friction when the switch is greatly reduced, Water Leakage phenomenon and can cut off the water supply construction not replace sealing ring.
And help to drink
Due to the internal body to non-toxic epoxy resin coating, gate of the inner and outer surfaces are completely coated with rubber and can not rust or corrosion of water available to drink.
- Casting valve
Valve body casting, precise geometry makes the body without any internal finishing to ensure that the valve seal.
And light weight
The valve is made of ductile cast, lighter in weight than conventional gate weight about 20%-30%. Convenient installation and repair.
- Q:I'm thinking about getting a Cold air intake along with a Bypass Valve to prevent Water Indigestion on my Toyota Corolla 07. I was wondering if Bypass Valves actually work and can someone explain to me the physics around it???( How bypass valves work)
- The AEM Bypass Valve protects the engine from ingesting water and hydro-locking if the filter becomes submerged in water. Hydro locking occurs when the end of the inlet pipe is submerged in water and the water is sucked into the engine. Driving the vehicle in rainy conditions is not enough to cause a problem unless the vehicle submerges enough that the inlet end of the pipe is immersed in water. Rain impingement on the filter will not cause a hydro lock condition. The distance of the filter from the road dictates the level of water that can cause damage. This distance varies with the vehicle ride height, which is why there are no published numbers for this measurement. We suggest taking this measurement and keeping it in a log book, so that in the event you encounter deep water you will know what your maximum allowable depth is before potential submersion of the inlet pipe. All AEM Cold Air Intake installations retain the factory splash shield (fender liner) for filter protection and performance. Removal of splash shield actually deteriorates performance by allowing air heated by the pavement to enter the filter and negates any positive pressure created in the air filter area when the vehicle is in motion. There are some instances where there is not enough room around the inlet pipe for adequate clearance of an Air Bypass Valve. In these instances, we recommend installing a Short Ram system if water ingestion is a concern.
- Q:i was told my egr valve needs to be replaced, so im wondering if the system cleaner will help at all. thanx
- well it depends if it needs to be replaced or just cleaned. shops wont tell you to get it clean because they want to chjarge u as much as possible. get sombody u know to clean it by taking it off and using a brush and degreaser. the fuel cleaner wont clean the egr valve it only cleans the combustion chamber.
- Q:I have 3 such valves in the line and none seem to be able to move past 10/4 oclock position and water remains on. Is there a way to adjust valve? Seems there is slot for screwdriver in center of valve.
- Pvc Shut Off Valve
- Q:Pressure relief valve on boiler is dripping.Starts to drip more when the boiler is turned on.Bad relief valve?
- Only to add what Steve said, make sure you have a pipe leading from the Safety valve to the floor, that way if the Safety valve let's go it won't be shooting straight at someone's face or other equipment. If you could, pipe the safety to a drain but by all means leave the line open, Put no other valve in the line to restrict what the safety is meant to do.
- Q:I am trying to remove my supply valve behind my toilet to replace but the valve wont come off. I am using a cresent wrench to turn it and it turns but does not unscrew. How can I remove this piece?
- If you have copper pipe behind this valve. you may be twisting the pipe. You must support the pipe while removing the valve. Good luck.
- Q:okay, well, I understand partials. But, on a trumpet, what does each valve do? I mean, I had this idea that each one was a half-step up from the previous...but that's not true. Is there some sort of pattern to them? Does each one have a different purpose?...Please answer as basically as possible. I don't play music very often, and I definitely don't speak brass-ish.
- 2nd okorder
- Q:what's the function of a car valve???????????
- the relatively valve would be unscrewed from the valve stem and adjusted. If t's the valve stem that desires changing that's achieved from interior the wheel/tyre blend. it would desire to be achieveable to deflate the tyre, push one section inwards off the rim and get to the valve stem, even yet it relatively is lots extra handy to take it to a tyre depot and characteristic it finished precise. the actual undertaking with a DIY job is getting the tyre sealed on the rim back. With an air line it relatively is undemanding to place air in quickly adequate to reseat the tyre, with a foot pump it relatively is totally very nearly impossible
- Q:Would a 96 saturn egr valve work on a 96 camaro
- Why would it. They are from different cars, with different engines.
- Q:What is the functional difference between the following:1. Blow Off Valve2. Dump Valve3. Bypass Valve4. Diverter Valve
- The blow-off valve releases boost pressure into the atomsphere when decelerating to avoid compressor surge. The dump valve bleeds out compressed air produced by the inertional rotation of the turbo impeller into the atomsphere when the throttle valve is closed. The bypass valve does the same thing as the blowoff valve, except that it recirculates the compressed air back into the intake instead of out into the atomsphere. Diverter valve is just another name for blowoff valve.
- Q:my dad's friend died, and dad had been keeping some valves of his. now we've been left with about 400 valves and i'm going to sell them.my main question is what are they used for? i need to write a description for ebay but have no idea what they're for! anyone know?also, how much should i sell them for? on the box it says 11 shillings, which i worked out as ?1.32, but how much should i sell them for on ebay? there's prices on ebay that are about 50p to ?1.50 for most of them, but some are about ?7 but have no bids at all. how much should i start the bidding at?also, if you could give me any other information that i should put in the description, i would really appretiate it :)they are mainly 'Mullard' valves (the company name) but some are 'MAZDA'thanks! :D
- It depends what they are, specifically. Valves used in TVs or RF receivers are not worth much. Audio and RF transmitter tubes might be worth something.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
DN600 Turbine Type Butterfly Valve with Hand wheel BS Standard
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords