DN50 Cast Iron Rubber Gate Valve with long stem

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Soft seal gate valve

Size:DN40mm-600mm

Design standard: DIN 3352/BS 5163/AWWA C509/JIS B2043

Test standard: DIN3230/BS 6755/AWWA C509/JIS B2003

End flange standard: DIN 2533 PN16/BS 4504 PN16/ANSI 150LB/JIS B2212 10K

Face to face standard: DIN 3202 F4/DIN 3202 F5/BS 5163/ANSI 16.10/JIS B2002

Body: Ductile iron/GGG50/A536

Wedge: Ductile iron+EPDM/Ductile iron+NBR

Stem: Brass/SS416/2Cr13

Bonnet: Ductile iron/GGG50

Handwheel: Ductile iron/GGG50

The products are widely used in water source projects, urban water supply and drainage, sewage treatment, eletric power, petroleum, petrochemical, heat supply, shipbuilding, medicine and metallurgy industries. Equipment are used for regulating or cutting off media in pipelines. Suitable media include water sewage, sea water, air, foodstuff and oil. Suitable for gear operators, electric and pneumatic control actuators.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Does the relief valve have a gate valve?
With the ball valve, needle valve, with the valve did not see, but there should be some.
Q:Which is more expensive, bronze gate valve or brass gate valve?
The casting and workability of brass are much better than that of stainless steel, especially the valve with more complicated internal cavity.
Q:Is the axial force and torque of the wedge gate valve the same?
The sealing performance is good, the gate valve is not easy to be jammed when heated, and is suitable for the parts with frequent switches. B is suitable for steam, high temperature oil and gas medium. C is not suitable for easy coking medium.
Q:What are the meaning of the cast rigid gate valves z41h-16c?
According to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== flange connection1== rigid single gateH== sealing surface material: Cr13 stainless steel16== pressure rating: 1.6MPaC== body material: carbon steel
Q:HVAC design, why is less than DN50 of pipe gate valve and cut-off valve,
I don't know why it was designed. Provide you with some information you refer to, I do not know if it works for you1, stop valve and gate valve are very expensive, more than DN50 can make a lot of money2, butterfly valve is only more than DN50, no small, there may be, but I almost can not see the market.3, like DN150, DN200 such cut-off valve, gate valve is very large, and the butterfly valve is relatively light, installation can save the cost of the block, the valve itself saves too much money.4, but most of the butterfly valve used for a long time are closed.
Q:What do you mean by gate valve type RVHX-0150-10 and Z45X-16Q?
Z45x-16q, Z means gate valve, 4 means flange connection, 5 refers to dark rod gate valve, X means rubber seal, 16 refers to nominal pressure 1.6MpaRVHX means manual gate valve, 150 refers to the caliber of DN150, and 10 indicates nominal pressure of 1.0MPa
Q:What is gate valve (with force transfer joint)?
The force transfer joint is mainly used for the loose connection of pumps, valves and other accessories.
Q:What are the features and uses of the gate valve?
What is gate valve? What is the purpose of forged steel gate valves? What are the features of forged steel gate valves?Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The gate valve movement direction perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The gate has two sealing surfaces, and the two sealing surfaces of the most commonly used gate valves form wedge and wedge angles vary with valve parameters. Gate valve drive classification: manual gate valve, pneumatic gate valve, electric gate valve.DefinitionGate valve means the closing of the valve (gate) along the central line of the vertical direction of the valve. The gate valve is mainly used for cutting in the pipeline.The valve is a valve with a very wide, cutting device general caliber DN = 50mm use it, sometimes a small diameter cutting device also use valve, gate valve has the following advantages:Fluid resistance is small.Minor force needed for opening and closing.Medium flow is unrestricted.When opening fully, the sealing surface is eroded by the working medium smaller than the cut-off valve.The shape is relatively simple and the casting process is betterValve also has shortcomings:The overall size and opening height are larger. Larger space required for installation.In the process of opening and closing, there is relative friction between the sealing surfaces, which may cause galling.Gate valve generally has two sealing surface, processing, grinding and maintenance to increase some difficulties.
Q:Does the tap belong to a stop valve or a gate valve?
When the valve is installed, the medium can enter from the bottom of the valve core and enter the two way from the top. Medium from the spool into the advantages of the valve closed when the packing is not under pressure, can extend the service life of the packing, and can be pressure in front of the valve in the case of replacement of packing work. Medium from the spool into the bottom of the shortcomings of the valve driving torque is larger, about 1.05~1.08 times above the entrance, the stem by the axial force of large, easy to bend the stem. To this end, the media from below to enter the way, generally only applicable to small caliber manual stop valve, to the valve closed, the media acting on the spool of force is not greater than 350kg limit. Electric cut-off valve is generally used to enter the media from the top way. The disadvantage of the medium entering from the top is just the opposite of the way it is entered below.Compared with the gate valve, the utility model has the advantages of simple structure, good sealing performance, and convenient manufacture and maintenance. The disadvantage is that the liquid resistance is large, and the opening and closing force is large. Gate and globe valves are fully open closed type valve, cut off or connected as the medium use, not as a control valve.The range of application of stop valves and gate valves is determined by their characteristics. In the smaller passages, the cut-off valve is used when required for better shutoff; in the steam pipe and the large diameter water supply pipe, the gate valve is generally used because of less fluid resistance.
Q:Why does the fire hydrant box in the air defense area need to be added with gate valves?
3, protective valve should be used for stainless steel or copper gate valve or cut-off valve;4, air defense enclosure structure, the distance from the proximal end of the valve should not be greater than 200mm. Valve should have obvious signs of opening and closing.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range