Q:On the pipe 1216141816202025, is it for 4 points, 5 points, 6 points, 1 inches of ground heating pipe?

Its advantages and disadvantages:(1) good mechanical performance;1., good pressure resistance, shock resistance, rupture resistance2., with a strong plastic deformation ability, can be greater than 5D radius within the arbitrary bending, without heating, not rebound; (D for pipe diameter)3. light weight, same flow diameter composite pipe weight is 1/3 of steel pipe, 1/12 of galvanized pipe;

Q:Phoney Tony used to love posing with factory workers wearing the fluorescent vest, hairnet, safety goggles etc. What a class act he was!

Tell her that if you will call her that and then she will get mad or drip hot sauce in her mouth

Q:Is your favorite color pink or not? Fire hydrants can be in many colors.

ExtensionsModule ManagerNewCustom HTML The rest is basic table structure and links This can be accomplished using html

Q:PE pipe joint and PPR joint can be with each other

Although these two materials belong to polyolefins, the molecular weight is different from that of molecular structure, so the melting point is different

Q:its a friend's birthday this weekend and he's planning on going to ocean beach in the bay area and throw a bonfire. just want to know what we should bring cause we never done that before? can we bring liquor beer? do a BBQ? do we need to reserve a fire pit? if so what time should we leave to reserve it? we're coming from Sacramento, ca. thank you in advance!

Let's dress up like apples and dance around the city singing I'm a gummy bear!

Q:The nozzle of a fire hose ejects water with a speed of 30.0 m/s. The stream of water is aimed 35 degrees above the horizontal ground. Assume the nozzle is at ground level, and each water drop is in free-fall.a. Find the speed of a water drop at the highest point of its motion.b. What is the magnitude of the acceleration of a water drop at the highest point of its motion?c. How far from the nozzle will the stream of water land?

The easiest and most cost effective way is to just replace them. Instructions are on the package. Good luck

Q:I need to talk about it in my physics class

Are you familiar with any type of soldering? There is low temp, and high temp, depending on the application, and the type of solder that you use. The most important thing to remember, is to thoroughly clean the inside of the fittings, and the end of the pipe. If you cut a pipe, make sure that you ream the inside, to restore the inner diameter of the pipe to its full bore dimension, otherwise, water will eat the pipes, from the inside, and you will have a premature breakdown in your piping system. A non acid, water soluble flux is required, again, so your pipes won't deteriorate from the inside. Low temp soldering can use a propane torch, but high temp, requires a hotter flame, to melt the solder. Practice on some pipes, before soldering for real. Never leave your flame in one spot too long. Doing so will cause the flux to be burned at that spot, and no solder will take at that spot, thus, ensuring a leak. Move your flame around the whole joint, heating it up uniformly, and concentrate your flame towards the center of the fitting, as solder will travel towards the heat. Good luck!

Q:if I don't have a hunting licence, but my girlfriend does, can I be with her while she hunts?

Here is one calculator that you can try. There are others on line that will do the same thing. The second link below has several water flow charts that can also be used to estimate flow rates.

Q:I am doing an experiment regarding the fluid flow phenomena. Does anybody come across this experiment mention above? I need some relevant websites which have this informations and the internal design of the valves. Thanks.

Maybe you can run in a temporary line from the compressor, connected to a branch with a valve. You will have to shut down whatever is on the other end until the connection is made, unless it has a valve fitted for this purpose. Another idea is to get a portable compressor or hire one for temporary use.

Q:Can you put auto locks in a 2001 sunfire that before didn't have any

PVC .. schedule 40.. Choose The yellow or cream colored PVC. Its for both hot and cold. Are you getting permit? You will need a 18 expansion tube on each line HOT/COLD above all fixtures. If you don't have the room , You can purchase a compact one ready made You really should get a permit. The best solution is to purchase a Basic Plumbing book. It may sound stupid BUT If you EVER sell your home, If its not correct,, The cost to do it TWICE is crazy. Just tring to helpDO IT RIGHT! DO IT ONCE! Think about it.