Q:What is the B axis of the NC table of the horizontal machining center and what is the mode of movement?

Rotational motion, that is, any angle of 360 degrees, or 360 degrees of motion, depends on whether it is one or 1/1000 degrees

Q:Bed electrical control technology, as shown in the diagram, ask: if the work station to run at both ends, want to stay for 10 seconds, how to control the design of the circuit?

A time relay in his one normally open contact to coil KM1, KM2 series electric locking loop, that is to say the motion of the platform to end, after the pressure switch, give him a ten seconds delay to contactor inversion of control power, so that we can realize that work Taiwan stop 10 seconds, ten seconds to remember to pay attention to the time relay is reset, the coil circuit loss of electricity, or directly to the other end of the reverse.

Q:CNC machine tools work surface milling a hole, do you know what method to repair it?

Upstairs, the method is 100 percent feasible ah.1. change the workbench2. milling the entire table may require technical guidance from the manufacturer

Q:What is the workbench?

Kam Tian kitchen utensils for you to answer: double deck table series products, are made of high-quality stainless steel, can also be customized according to user requirements. The panel is made of mould and formed by bending at once. It is smooth and natural without solder joints. It is easier to clean and durable, and never loosen.

Q:I want to install the cylinder on the rotary table. I want to use pneumatic rotary joint to solve the problem of trachea winding. Can you tell me if the rotary joint is connected to the cylinder or what?

It's so complicated. Generally, the joints can be rotated at a certain angle, but if you turn the circle, the pipe may be twistedYou don't seem to be able to solve the problem of trachea entanglement with this method.. If you have any doubts, you can consult E.MC's Pneumatic technologist directly

Q:Two are all right, check the information, and now the rotary table has two benchmark surface, vertical and horizontal dual-use, coupled with servo motor drive, indexing is also no problem.

No, the indexing head is a rotating shaft parallel to the horizontal plane of the work tableThe rotary table is usually vertical to the horizontal surface, and it does not necessarily have an indexing device

Q:The working principle of the machine table of the left and right!!! Please, urgently.

Working principle of machine tool table: it is mainly used in the plane of machine tool working. There are holes and T groove on it. It is used to fix the workpiece and clean the iron filings produced during the process. Manufactured according to JB/T7974-99 standard, the products are made of ribs, plates and boxes. The working face is scraped and scraped, and V, T, U and round holes and long holes can be machined on the working face.Features of machine tool table: moisture resistance, corrosion resistance, non fading, low temperature coefficient and so onMaterial requirementsMachine tool table material: after two manual processing (artificial annealing 600 degrees -700 degrees and natural aging 2-3 years), the use of the product precision stability, good wear resistance.Specification parameterMachine size: 300mm * 300mm 3000mm * 6000mm (according to the machine table a variety of customized user requirements) machine precision: according to the implementation of the national standard verification procedures, respectively 0, 1, 2, 3 and four grades.

Q:Who knows how to connect the NC rotary table to the CNC system? Is the main control signal line sensor and a pneumatic valve power supply line (I use the pneumatic clamping), can provide the copy of the relevant instructions?

You need the machine instruction, most control signal belongs to the digital switching signal should be connected to the i/o interface, you can view the parameter menu in the CNC system, a brief description of the parameters are provided in most systems, can reference connection!

Q:What is the kn table

Ha, Taobao sellers used to trade, change prices, delivery, customer chat, with the first Oh!

Q:Do you have anything on the car bench?

Do not put it better, it affects sight, and high light objects in the sun or toward the high beam, it is easy to refract light to the driver, especially dazzling. The second is that in an emergency, for example, when a car is hit, it is easy to fly or injure people