DIA25 to DIA150 Steel Grinding Ball for Cement and Mineral Processing in Top Quality

Ref Price:
Loading Port:
Qingdao Port
Payment Terms:
TT or LC
Min Order Qty:
25M.T. m.t.
Supply Capability:
200000M.T./Year m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Feature of Rolling Forged Steel Grinding Ball with Supper Hardness apply for all kinds of Mineral Processing

  1. 1)In general, grinding steel ball has high hardness: surface hardness to 58-65 HRC, volume hardness of 56-65 HRC 

  2.  2)Impact toughness high: impact toughness more than 12 J / cm2

  3.  3)Broken rate is low: the actual broken rate is not higher than 0.5%. 

  4.  4)Loss of grinding forged steel ball round rate is low. 

Applied fields of Rolling Forged Steel Grinding Ball with Supper Hardness apply for all kinds of Mineral Processing

  1. 1)Metal Mines,  2) Cement plants,  

  2. 3) Power stations, 4) Chemical industry 

Chemical Elements of Rolling Forged Steel Grinding Ball with Supper Hardness apply for all kinds of Mineral Processing

Material

C

Mn

Si

Cr

S

P

V

50Mn

0.48-0.56

0.70-1.0

0.17-0.37

≤0.25

≤0.035

≤0.035

60Mn

0.57-0.65

0.70-1.0

0.17-0.37

≤0.25

≤0.035

≤0.035

65Mn

0.60-0.70

0.90-1.20

0.17-0.37

≤0.25

≤0.035

≤0.035

75Mn

0.72-0.92

0.17-0.37

0.17-0.37

0.4-0.6

≤0.035

≤0.035

75MnCr

0.70-0.85

0.7-0.8

0.17-0.37

0.2-0.7

≤0.03

≤0.03

75SiMn

0.70-0.90

0.7-1.2

0.4-0.8

≤0.25

≤0.03

≤0.03

Wear-resistant Alloy

0.5-0.65

0.4-1.0

1.4-1.8

0.9-1.2

≤0.03

≤0.03

0.1-0.2

 

Material

C

Si

Cr

Mn

S

P

Cr-22-32%

2.0-2.8

≤1.0

22-32

0.5-2.0

≤0.06

≤0.08

Cr-17-22%

2.0-2.8

≤1.0

17-22

0.5-2.0

≤0.06

≤0.08

Cr-15-17%

2.2-3.0

≤1.0

15-17

0.5-2.0

≤0.06

≤0.08

Cr-11-14%

2.2-3.2

≤1.0

11-14

0.5-2.5

≤0.06

≤0.08

 

 

 

 

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:ZGMn13 casting parts processing, with what knife head good?
The ZGMn13 itself is not have processing, if only the processing point, sharpening, ordinary can, if the processing area is relatively large, ZGMn13 external impact load is bigger,
Q:What is the difference between forging parts and casting parts?
Forging is in hot state through the metal hammer or press equipment produced by forging parts. A casting is a metal that is liquid and is poured into a cavity of a specified shape and cooled and solidified. It is the forging metal soft pinch molding, and casting the metal into thin cooling solidification.Forged parts are costly and have long production cycles.
Q:What are the requirements for casting steel castings?
1, high quality requirements of the surface or the main processing surface should be placed below.
Q:Heat treatment process and purpose of casting parts
Objective: to stabilize tissues, eliminate or substantially reduce internal stress.
Q:When there is no flaw detection for large casting parts, is there any crack inside?
Cracks are considered serious levels of defects and should be repaired
Q:The casting sand is going on
2, causes(1) sand mold (core) strength is not high, when the box a little reason will fall off.(2) the strength of sand mould (core) is not high, it can not stand the erosion of molten steel.(3) box sand mould (core) crush.(4) high strength under high temperature, warpage, deformation and protuberance into the cast steel under the action of high temperature molten steel.(5) the floating sand in the air hole of the sand mold falls, especially when the floating sand falls in the casting, and the floating sand on the surface of the sand mold is easy to fall through the air vent.(6) when the box is closed, the surface of the mold cavity and the surface of the sand core are not cleaned, and the sand (core) surface has floating sand and so on.
Q:The casting defects of pores, trachoma how to repair?
Airhole above 2mm recommended LT101 casting defect repair agent. If repair quality requirements, high availability LT111 iron repair agent, LT112 steel repair agent, LT113 aluminum repair agent, LT114 copper repair agent.
Q:Casting pieces of plastic processing requirements can not fall off the skin,
The pre treatment temperature and the quality of plastic powder are likely to be problems
Q:Casting parts in rocker arm drilling, reaming, roughness, block.
The finish of reaming depends on the material and the sharpness of the reamer, as well as the speed and speed of the top and bottom. Marine machine tool
Q:Selection of hydraulic press is the casting parts and steel plate welding, how to choose?
Casting parts in one shape, the overall processing in this regard than steel plate welding better. The same price is much more expensive than steel. Large hydraulic presses seldom have casting parts.
CDE is one of the largest factory specialized in producing Forged Grinding Balls and Cast Grinding Balls in China. Our annual production of grinding balls is about 100,000 ton. Our company has passed ISO9001: 2000 quality system authentication. We mainly export our grinding balls to Chile, Peru, Ghana, Argentina, Philippine, South-Africa, Italy, Japan, Korea, India, Australia etc more than 20 countries and areas.

1. Manufacturer Overview

Location Shandong, China
Year Established 1971
Annual Output Value US$50 Million - US$100 Million
Main Markets Domestic Market, Southeast Asia, South Asia, North America, South America
Company Certifications ISO9001;IS014001 Certificate

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Qingdao Port
Export Percentage
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese, Korean
b)Factory Information  
Factory Size: Above 60,000 square meters
No. of Production Lines Above 10
Contract Manufacturing Forged Grinding Ball,Cast Grinding Ball,Casting Cylpebs,Grinding Rods,Decorative Steel Ball
Product Price Range Average