Q:How is the glass curtain wall attached to the steel frame fixed on the steel frame

Steel structure point curtain wall cylindrical adapter seat welded to the steel structure, the splicing claw screw to the adapter seat, the joint and then fixed to the splicing claw

Q:What are the metal members connecting the glass and the glass ribs in the glass curtain wall?

Called the claws. The splicing jaws are mainly used as support joints and transfer loads to a fixed support structure, which is an important accessory to the glass curtain wall.

Q:The installation method of the splicing jaws

Steel beams and glass are ready to ensure that the location is not wrong, as well as glass holes, adapter and steel beam welding no problem. Put the claws on the transfer, engage in tight. Put the splice on the glass, engage in tight, do not forget the middle of the gasket. Then, the glass is mounted, the splice is connected with the splicing jaws, but do not twist too tightly, and then adjust the position and adjust the error. Finally, tighten, check the next to ensure safety. Ordinary is so loaded, of course, there are different styles, installation methods are different, but not difficult.

Q:Glass curtain wall claw should be how to calculate the size

In general, our factory will be based on the customer's glass area and glass thickness, to advise customers to choose what specifications of the split jaws, common splicing claw specifications are: 150.160.200.220.250 and so on. Be sure to choose the appropriate type and specification of the splicing jaws so that both price and performance are guaranteed

Q:The production of curtain wall glass splicing claws of the big brand which several!

In accordance with the light box instructions to open to their company to see their factory has not a basketball court, and inside a few lathes, inside the factory inside the office there are several pieces of claw samples, the production of claw pieces of a machine are not, This scale

Q:Glass curtain wall glass installation process requirements which out

The last step is the most critical step is to glue. Before the application of "xylene" or industrial ethanol and clean towels to wipe the stainless steel and steel tiles to fight the site, in the need to glue part of the paste protective tape, pay attention to adhesive tape and glue to be straight. Split the bottom of the stainless steel and the gap with the steel slot with a foam tape to tighten, to ensure straight, and set the net height of 8mm-12mm of the adhesive thickness. When the glue is full, the operation sequence is generally: first hit the horizontal seam after playing vertical seam; vertical glue should be from top to bottom, glue filled, should check whether there are bubbles, empty, broken, Mixed, if it should be dealt with in a timely manner. Every other day when the plastic joints, plastic joints should be cleaned up a good plastic head, remove the glue before the glue, to ensure that the two glue the connection closely. Stainless steel glue should be quickly modified after the adhesive tape will be torn on stainless steel, stainless steel plastic curing, should clean the inside and outside the stainless steel, do a good job protection signs. If the use of laminated stainless steel, the outer film thickness should not be less than 10mm, the thickness of the film should not be less than 8mm.

Q:Do you want to glue when you install a splice?

Are mechanically connected by bolts.

Q:How many errors can be made by welding the splicing jaws

To be reasonable at the beginning of the adapter and the steel frame between the contacts designed, I make a simple example: Now there are a lot of steel frame is welded with a round tube, that adapter The base in the production of the time also need to be cut into the arc, so that steel pipe can be better connected to the tube, while reducing the interface of the degree of restraint, and secondly, reasonable arrangement of welding order to reduce the welding stress, Welding at the same time can reduce the heat generated when welding cracks. Welding starting point and the mouth is easy to produce cracks, conditional welding joints should be at the plus arc plate and arc plate. If you can not use the arc plate, the best use of attenuation current arc, and fill the crater. At the same time in the welding process in order to reduce the weld cracks, as far as possible the use of small lines of energy and cross-section of the welding point. If the process of welding found in the leak, if not serious, then gently knock with a hammer may be just fine. To avoid this is best to the workers carefully, in the welding when the cautious point of these problems can be avoided.

Q:Clip glass with a handrail pieces of how much money, large amount of where the wholesale right

Handrails and general handrails supporting the column, according to the batch of more cost-effective, not expensive parts, due to changes in raw materials

Q:What is the difference between double steel safety glass and insulating glass in steel canopy

Rainforest belongs to the zenith glass Can not use the insulating glass In accordance with the requirements of the specification requires the use of single-steel clamp or double-tempered glass or tempered plastic hollow glass to pass the acceptance Insulating glass is characterized by the insulation of the noise canopy is not a closed environment so can not highlight the effect of insulating glass so if the shed with hollow glass not only can not be qualified and is also a waste