cu wire armored cable To be laid indoors, in tunnel, cable furrow or pipe

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
100 m
Supply Capability:
30000 m/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 Product Introduction

Be applicable to the well, water inside and fall in the bad soil, the cable can bear the equal dint outside the machine with pull the dint
.

 

Operating Characteristics:

The single-core magnetism material packs the cable is not suitable for to use for the AC power supply back track, the necessity hour eligibility uses the single-core 62 or 72 type pack the cable.
In order to prevent resulting in the descent of the cable transport electric current ability.Disallow the cent to cross the magnetism piping mutually when single-core cable establish.Be applicable to the well, underwater with the bottom of sea, the cable can bear the bigger pressure with lead to pull the dint

 

Specification: 

 


 U0/Um(kv)
 
No.of Core
1st class0.6/11.8/33.6/66/108.7/1512/2018/3021/35
2nd class1/13/36/68.7/1012/1518/20-26/35
1 CoreSection
area(mm2)
1.5-80025-80025-80025-80035-80050-80050-80050-800
2 CoreSection
Area(mm2)
1.5-185/ / / / / / /
3 CoreSection
area(mm2)
1.5-40025-40025-40025-40035-40050-40050-40050-400
4 CoreSection
Area(mm2)
2.5-40025-400 / /////
5 CoreSection
area(mm2)
2.5-40025-400///  ///


 

 

 cu wire armored cable To be laid indoors, in tunnel, cable furrow or pipe

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Power supply missing cables?
There's 2 types of power connectors, old style 4-pin Molex and Sata power. Adapters are pretty cheap, just check Monoprice.
Q:Do data cables for dvd drives/hard drives ome with the drive or psu or motherboard?
Yes! the cables are included with the products. Your Power Supply even comes with power cord.
Q:How to connect power cables back to the motherboard?
If your talking about the power cables from the power supply to the motherboard those are fairly straight forward. It is a 20 or, 24 pin connector. Usually along the edge opposite the external connections for the motherboard. Although, the placement really depends on the manufacturer and, could even be near the middle of the board. They are keyed and, you can not plug them in incorrectly. As long as you don't force them into the slot. If your speaking of the wires from the case to the motherboard that is a little more difficult. P3 and, P4 motherboards usually have a keyed connection that simply plugs in. Other boards have markings on each of the wires corresponding with it's connection. The one thing that is the same for every board is that the two black wires must be side by side. If you've never done it before you should have labeled each wire and, made a diagram of their placement. Your best hope short of taking your computer to the local shop is to try and, find diagrams for both your motherboard and, the case.
Q:Playstation 3 power cable/AC cable question?
My PS3 slim does not use the standard 3-prong power cord. However, Googling for images of PS3 power cords, it shows the standard 3-prong. So the answer yes or no.
Q:Amp power cable wont fit on battery?
I'm not quite sure how your trying to attach it to the battery, but you should be able to take the ring and slide it over the the little bolt that is on your terminal. After that just tighten the nut over it. If this isn't working you may want to invest in a aftermarket terminal. They're pretty cheap and depending on the one you get you should be able to hook it up with the ring on the end or strip it and connect it using whatever method the instructions say.
Q:i have power in half of the power cable connected to my amp, how can i fix it?
I okorder.com/... Under the column for 90 degree cable in copper pick the wire gauge that is closest to your amp requirements without being under. For example: 1200 watt amp = 100 amps of power 2 gauge copper can handle 130 amps (This chart is missing 3 gauge which some places do carry, which can handle 110 amps) 4 gauge is only good for 95 amps. These ratings are about heat build up from inductance of the current. When the heat exceeds the rating, the sheathing melts and conductor degrades at it's weakest point. I recommend use of THHN electrical wire. It is gas and oil resistant and has heavy strands that hold up well to the stress of vehicle install situations. If your wire and fuses are properly sized, then check all of your connections. Often times heat and vibration will loosen screws on amplifier contacts. Also, under the hood, heat can melt your fuse holder causing plastic to coat the contact points (in which case you'll need a small file to clean the contacts) There's really a lot of possibilities here and your question is quite vague and convoluted. Please give more details or take some time and analyse the problem carefully. Chances are that you will discover the source of the problem in a matter of just 15 minutes or so of checking.
Q:dell printer 922 power cable.. ?
visit OKorder
Q:What kind of material should be selected for the fixing bracket of the cable trunking
General 2.5 square wire load is 2 kilowatts, and rubber sheathed cable, full load can reach 3 kilowatts are no problem (estimated again, it is not safe). The load level of the wire is mainly dependent on the current, but also on the voltage level. Under normal circumstances 50A below 1 square millimeter safe carrying capacity is 6A, 50 ~ 100A current 1 square millimeter of the safe carrying capacity is 5A, 100A current above the general take 1 square millimeter of the safe current is 2.5A; so many large square copper cable You can calculate the current. According to the three-phase alternating current formula: P = 1.732 * U * I * cosφ, cosφ is the power factor, select 0.8; this is the three-phase power calculation formula. Single phase: P = U * I * cosφ, cosφ is the power factor The power factor is 1 for the resistive load and 0.8 for the inductive load.
Q:What are the advantages and disadvantages of separating 28Vdc, 200A positive power cables and returns into two?
WHAT ARE YOU TALKING ABOUT ? ALL DC POWER SOURCE REQUIRES TWO SEPARATED CABLES .
Q:Power cable ZRYJV-4x70 + 1x35 What does it mean?
2 cable in a variety of environments in the laying of the layout, spacing should meet the design requirements

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range