Concentric overhead conducting wire JL/LHA1 JL/LHA2

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
200 m
Supply Capability:
100000 m/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product properties:  

1. The long-term working temperature allowed by overhead conducting wires is 70°C;  

2. When there are large-span rare weather conditions and there is less ice coating occurring in heavy ice areas, maximum stress the lowest point of the conductor sag should not be more than 60% of instantaneous destructive power;

3. When the wires are connected, strands around the connecting pipe should not bulge, otherwise the strands of wires in operation will be unevenly stressed, after the joints are pressed, outlets of connecting pipe should be covered with moisture-proof paint to prevent corrosion; 

4. When the wires are installed, sag stress of all the wires at the same gear should be the same, and within the range permitted by the limited distances to the ground and exceeding the distance for protection of building, the conducting wire stress can be higher by 10-15% than normal tension.  Scope of application:  This product is applied to overhead power transmission and distribution lines.


Scope of application:

This product is applied to overhead power transmission and distribution lines.


Type and Specification:

New Type

Original type

Description

Specification No.

JL

LJ

Aluminum stranded wire

10--1500

JL/G1A  JL/G1B

LGJ

Steel cored aluminum stranded wire

16--1250

JL/G1AF  JL/G2AF

LGJF

Anti-corrosion steel cored aluminum   stranded wire

16--1250

JLHA1   JLHA2

LHAJ

Aluminum alloy stranded wire

16--1250

JLHA1/G1A  JLHA2/G1A

LHAGJ

Steel cored aluminum alloy stranded   wire

16--1120

JL/LHA1  JL/LHA2

LLHAGJ

Aluminum alloy cored aluminum stranded   wire

16--1400

JG1A  JG1B  JG2A  G3A

GJ

Steel stranded wire

6--63

JLB1A  JLB1B JLB2

LBGJ

Aluminum-clad steel stranded wire

4--200






Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Need Help Finding Alternator Power Cable?
usually only power wires run to the alternator, most arent grounded by a wire, they are grounded through their case and the mounting brakets to the engine, but all charging systems are a little different. I see your ground runs to the mounting bolt, and so that wire that goes to the mounting bolt on the alternator would be your ground wire to the battery. the large wire on the back of the alternator in your picture has BAT beside it, that is the wire that would be the power wire back out to the battery. i would suggest to get a haynes or chilton manual for this specific vehicle if your not sure of things such as this.
Q:If my Epson Stylus Color Printer doesn't turn on, can i get another power cable for it?
That's was my problem too. I let my garage to use it and buy another brand.I think you have to re-install it.Maybe it was corrupted.
Q:Can i switch power supply cables ?
hardship examining your question. Are you asserting which you have microprocessor that hangs once you're utilising a generator? is the generator powering the microprocessor? sure, interestingly that noise spikes or another noise from the generator is inflicting the reminiscence interior the processor to be changed. Is the processor in a shielded field? the ability grant? Are there any filters on the generator? all of those can help. Are there any archives lines linked to the processor? they could be the best suspects. they might could be shielded.
Q:What can be done to prevent the power cable on a Toshiba Satellite A215 laptop from burning up again?
It would have to be a combination of things that made it fray. Like, for example, being bent at an extreme angle while in use for long periods of time. Power cables get hot from normal use. The plastic insulation gets soft. If the power cable is laid in a comfortable position, if it is allowed to cool before being wrapped up, and there are no problems with the power adapter port on the laptop, a power adapter cable will last for the life of the laptop. Now, if you are using a Universal power brick, that is part of your problem. This laptop only requires a 65 watt adapter. Universal power adapters will push more juice to your laptop... up to 90 watts. This will cause the cables to get hotter. So, if you have not replaced it with a 19 volt 3.42amp brick specifically designed to work with your laptop... then you should do so. And feel free to buy one off OKorder. Same brick as what you get from Toshiba, for a fraction of the cost. end of line
Q:Can I use the power cable to my laptop AC in countries with 240V?
The thinner the cables are, the less voltage they can handle. So since cell phone charger cables are significantly smaller than laptop cables, the cell phone charger cables could heat up and actually melt the insulation.
Q:Is it ok to have only one power supply cable in the motherboard?
I'm sorry but no you need to have all the correct plugs installed if you expect them to run correctly. You didn't really give any info about the power supply but for that graphics card you generally want between 550-600 watt power supply to run anyways. Sounds like you will either need the proper adapters or another power supply altogether.
Q:What does the cable (YJV-5 * 6) mean?
Full name: cable ZR-YJV22-4 * 16MM2ZR: flame retardant ----- YJV22: copper conductor cross-linked polyethylene insulated PVC sheathed double steel belt wrapped armored power cable --- 4 * 16MM2: 4 core, each core 16 square millimeters.
Q:i have a laptop, and the socket where the power cable goes, stopped working.?
This is a common problem with the technology. Our shop charges 150.00 to resolder the jack on. You have to completely remove the motherboard from the case inorder to properly fix the jack. This problem will repeat with time so extra care should be taken then using AC Power.
Q:Buy new power cable? or adapter?
It would be better to get a new power cable, if you get an adaptor the connection might not be as reliable as it could become loose and there would be two connections between computer and power.
Q:How do I repair the power cable on my vintage sewing machine?
Split the power cable... Skin the insulation back on the individual wires..Keep track of the colors.... Split one side far enough back to put pieces of shrink tubing on the individual wires...put the approcate wires in an insulated butt splicer....crimp the splicers...Heat shrink the tubing...Then tape the individual leads with 3M-130c rubber tape ..Then put about 2-3 layers of 3M 88 tape on top of the rubber tape....It will last as long as you will Have A Good Day

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range