Cobrahead Area/ Street Light (Small) C0830-JR/KR

Chat Online

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Product Features

●Exterior curved design,simple and sleek

●The housing is composed of high quality die-cast aluminum

●AC90～264V wide input voltage range

●Operating Temp -40℃～+55℃

●Intelligent dimming control system to achieve secondary level energy saving

Cobrahead Area/ Street Light (Small) C0830-JR/KR

Technical Parameters

Size Chart(mm) C0830-JR C0830-KR

Cobrahead Area/ Street Light (Small) C0830-JR/KR

Light Distribution Curve C0830-JR/KR

Cobrahead Area/ Street Light (Small) C0830-JR/KR

Q:What's the reason that the LED street lights flash out?: In addition, there may be LED damage. Among them, LED short-circuit, resulting in the number of LED series to reduce, LED voltage at both ends of low, low beyond the power output voltage range, at this time the power will protect, there will be flash phenomenon.

Q:What is the display index of the LED lamp?: The degree to which an object's color is rendered is called color rendering.Usually called the color rendering index (Ra)A light source with a Ra value of 100 indicates that the color displayed in the light of the object is consistent with that under the standard light source.

Q:How much is the power supply voltage of street lamp LED?: 220V AC through the LED power, converted to DC 35V voltage supply to the chip, LED chip can only withstand DC 35V voltage!

Q:What are the requirements of the LED street lamp chip? How big is it? How many will it take and how big is the distance between them?: To single words, whatever you want a few watts, is generally the number of beads multiples of 7. A single chip is usually 45U, specifically you want what brand, the price is not the same.

Q:22 km road, every 33 meters to install a street lamp, street light power 120W, attached to the LED display 60W, a total of 180W, seeking the best laying line program: If there are 10 or so parallel units. Each unit of parallel =0.18x60=10.8KW, 16mm - 25mm - copper or aluminum wire. Light controlled single-phase AC contactor 100A.

Q:The 6 meter high watt LED bulb lamp should match: Generally equipped with 30W led, Yangzhou is the country's largest production base of street lights, manufacturers can visit to see.

Q:What are the components of the LED street lamp holder structure?: LED street lamp holder adopts aluminum alloy die-casting molding, it can effectively heat radiation and waterproof, dustproof.

Q:What are the components of a solar street lamp?: Solar panels used to transform solar energy into electrical energy; solar controller: used to charge and discharge the battery, also the battery charge, over discharge protection and timing switch for LED lamps; battery: electrical energy use for storing solar panels; LED lights: used for lighting in the night thank you!

Q:Excuse me, LED experts. How many watts do LED street lights usually have on the roads?: The most common sodium lamps for street lamps are 100W, 150W, 250W, 400W

Q:What are the parts of a LED street lamp?: Solar energy is one of the most direct the most clean energy, solar energy is a huge amount of renewable energy, each day to reach the earth's surface radiation can be approximately equal to 2.5 millions of barrels of oil, can be said to be inexhaustible. The LED spectra of almost all concentrated in the visible light spectrum, so high luminous efficiency, is generally believed that energy-saving lamp energy-saving 4/5 is a great initiative, but also energy-saving energy-saving lamp LED than 1/4, this is a great reform of solid light source. Solar LED lighting integrates the advantages of solar energy and LED.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range