Mainly used for conveying water,oil,acid-base solution,emulsion,suspoemulsion and liquid metal,as well as azeotropic mixture and liquid containing suspended solids.
- Q:Engine room abnormal sound! Excuse me, is this the reason for the oil pump?
- The oil shortage caused by the oil pump jam is insufficient
- Q:TOYOTA Camry oil pump how to change?
- Feel shy, just wrong is oil pounds instead of gasoline oil to pound, pound the oil pan removed then the timing chain cover with chain are removed, it can remove the oil pound, because the more complex suggest that you find a professional repair shop processing.
- Q:What is the difference between an oil pump and a gear pump?
- The oil pump and the gear pump all play the lubrication role, the engine oil pump is delivers the engine oil each to lubricate the part, but the gear pump is 2 or more gears, when works, gives him the fuel injection
- Q:What are the fuel pump inspection items for diesel generator sets?
- The main inspection items are as follows:1, the outer rotor and pump casing pump clearance;2, the internal and external rotor meshing clearance;3, rotor and pump cover face clearance;4. Flatness of pump cover.[diesel generator unit oil pump inspection notice]1, check valve planes such as abrasion, sag, pitting phenomenon, application of grinding paste on the plate grinding, severe cases should be renewed.2. The surface of the one-way valve seat on the shell should be replaced when worn or not smooth.3, the top rod and the top sleeve wear seriously, so that the gap increases, the seal becomes worse, diesel leakage seriously, you need to replace with the shell, or choose the enlarged size of the top rod, but need to pass mutual research.4, the coarse strainer tubing joints within the core, and easy to be cottony sundries plug, effect of fuel supply, it should always pay attention to the clean fuel and remove the dirt on the filter core.5, the hand pump piston rubber ring damaged, should be replaced in good time. After the center of gravity of the oil pump is assembled, the moving parts of the piston, the ejector rod and the other parts of the oil pump are required to be in good motion during the whole journey, and no blocking and blocking are allowed. The hand pump should be light and flexible. Pay attention to the installation of the one-way valve spring. The check valve spring must be accurately embedded in the spring slot.
- Q:What are the problems caused by engine oil pump damage?
- Hello, the oil pump damage, will lead to insufficient oil or will not provide oil in the body parts of the lubrication, such as the size of the tile can not get the lubrication of oil, so that lead to burning tiles and other phenomena, thank you for reference
- Q:The working principle of gear type oil pump
- What are the working principles and characteristics of gear pumps? The gear pump is a volume type rotary pump, its working principle is: the gear pump has a pair of meshing gears, gear (wheel) fixed on the drive shaft and the shaft end of the gear pump extends out of the casing is driven by a prime mover, a gear pump (driven) installed on the other a shaft gear rotates, the gear pump, the liquid into the suction space along the suction pipe, along the upper and lower shell wall by two gears are respectively extruded into a discharge space (tooth and tooth before confluence), and then enter the pressure discharge tubing. The main features of gear pumps are compact structure, small size, light weight and low cost. Compared with other types of pumps, it has the disadvantages of low efficiency, large vibration, large noise and easy wear
- Q:Automobile oil pump fault
- Such a problem can arise. The oil pressure is too high, and the oil filter is opened by "drum". The reason is that the oil pump pressure limiting valve [pressure relief valve], resulting in a failure, can not normally open at high pressure caused by pressure relief.
- Q:Does the motorcycle oil pump break down and cause the engine oil to burn?
- The pits are ready for oil, lubrication, and burning
- Q:TOYOTA oil pump not going off
- Hello, it may be clogged with oil pump strainer! It is also possible that the oil pump is broken! It is recommended to disassemble the oil drop shell!
- Q:What's the reason that I changed the new oil pump instead of the engine oil?
- Did you try the oil pump before loading?
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average